The Bathurst Channel marine habitat layer - 1: 25,000 depicts marine habitats for the entire channel from the inside of the Breaksea Islands to Nixson Point [145d 55m, -43d 18m] to [146d 08m, -43d 21m]. The habitat types depicted in the dataset include silt, silty sand, hard sand and low profile reef. The data was collected in October and November 2002 by marine researchers at the Tasmanian Aquaculture and Fisheries Institute. The use of underwater camera equipment, echo sounder data and a Differential GPS unit allowed for the extensive area to be surveyed. The dataset is intended to be used to fulfil coastal management objectives according to The Living Marine Resources Act 1995

The Macquarie Harbour - 1:25,000 Series depicts bathymetric contours from Hells Gate [145d 13m, -42d 13m] to the mouth of the Gordon River [145d 31m, -42d 26m]. The contours are at 5 metre intervals. The dataset is intended to be used to fulfil coastal management objectives according to The Living Marine Resources Act 1995. It is not to be used for navigational purposes.

The Bathymetric Contour layer depicts depth information for approximately 150 kilometers around Tasmania at 100 meter intervals.

Bathymetric contours (5 m interval) for Tasmanian coastal waters from the LWM (Low water mark) to 40 metres in depth or 1.5 kms from shore (whichever boundary is first identified). Detailed bathymetric contours were developed to be used to fulfill coastal management objectives according to The Living Marine Resources Act 1995.

Bathymetric contours (5 m interval) for Tasmanian coastal waters from the LWM (Low water mark) to 40 metres in depth or 1.5 kms from shore (whichever boundary is first identified). Detailed bathymetric contours were developed to be used to fulfill coastal management objectives according to The Living Marine Resources Act 1995.

The Kent Group marine contour map 1:25000 depicts bathymetric contours from the coastlines of the islands of the Kent Group to the 3nm offshore limit. The contour intervals are at 5 metres. The dataset is intended to be used to fulfil coastal management objectives according to The Living Marine Resources Act 1995 and is not to be used for navigational purposes.

The north western Tasmania Bathymetry 1:25000 depicts bathymetric contours from Robbins Island [144deg 53min, -40deg 44min] to West Head [146deg 43min, -41deg 44min] from the coastline to 1500m from the coastline. The contour intervals are at 2 metre intervals. The dataset is intended to be used to fulfil coastal management objectives according to The Living Marine Resources Act 1995 and to support Natural Resource management priorities in the Northern NRM region of Tasmania. It is not to be used for navigational purposes.

These data were collected under a cooperative agreement between the Massachusetts Office of Coastal Zone Management (CZM) and the U.S. Geological Survey (USGS), Coastal and Marine Geology Program, Woods Hole Coastal and Marine Science Center (WHCMSC). Initiated in 2003, the primary objective of this program is to develop regional geologic framework information for the management of coastal and marine resources. Accurate data and maps of seafloor geology are important first steps toward protecting fish habitat, delineating marine resources, and assessing environmental changes due to natural or human impacts. The project is focused on the inshore waters of coastal Massachusetts, primarily in water depths of 2-30 meters. Data collected for the mapping cooperative have been released in a series of USGS Open-File Reports (). The data collected in this study area located around the western extent of the Elizabeth Islands includes high resolution bathymetry, acoustic-backscatter intensity, seismic-reflection, and navigation data. These data were collected during a nearshore cruise in September 2010 onboard the R/V Rafael using the following equipment: an SEA Ltd SwathPlus interferometric sonar (234 kHz), Klein 3000 dual frequency sidescan sonar, an Edgetech 424 chirp subbottom profiling system, and 4 GPS antennae. More information about the cruise conducted as part of the project: Geologic Mapping of the Seafloor Offshore of Massachusetts can be found on the Woods Hole Coastal and Marine Science Center Field Activity webpage:

These data were collected under a cooperative agreement between the Massachusetts Office of Coastal Zone Management (CZM) and the U.S. Geological Survey (USGS), Coastal and Marine Geology Program, Woods Hole Coastal and Marine Science Center (WHCMSC). Initiated in 2003, the primary objective of this program is to develop regional geologic framework information for the management of coastal and marine resources. Accurate data and maps of seafloor geology are important first steps toward protecting fish habitat, delineating marine resources, and assessing environmental changes due to natural or human impacts. The project is focused on the inshore waters of coastal Massachusetts, primarily in water depths of 2-30 meters. Data collected for the mapping cooperative have been released in a series of USGS Open-File Reports (). The data collected in this study area located around the western extent of the Elizabeth Islands includes high resolution bathymetry, acoustic-backscatter intensity, seismic-reflection, and navigation data. These data were collected during a nearshore cruise in September 2010 onboard the R/V Rafael using the following equipment: an SEA Ltd SwathPlus interferometric sonar (234 kHz), Klein 3000 dual frequency sidescan sonar, an Edgetech 424 chirp subbottom profiling system, and 4 GPS antennae. More information about the cruise conducted as part of the project: Geologic Mapping of the Seafloor Offshore of Massachusetts can be found on the Woods Hole Coastal and Marine Science Center Field Activity webpage:

This dataset contains contours generated from the Australian bathymetry and topography grid, June 2009 version 4 by Geoscience Australia. It contains depth contours for -20m, -40m, -100m, -200m and -400m. Contours were generated in ArcMap using the Spatial Analyst Tools / Surface / Contour List tool. This output was then simplified using the Cartography Tools / Generalization / Smooth Line with a tolerance of 300m. The rest of this documentation is based on the metadata of the Australian bathymetry and topography grid itself. This grid is available from GA at http://dx.doi.org/10.4225/25/53D99B6581B9A . In 2005 Geoscience Australia and the National Oceans Office undertook a joint project to produce a consistent, high-quality 9 arc second (0.0025 deg or ~250m at the equator) bathymetric grid for Australian waters. In 2009 a number of new datasets were included in an updated version of the grid. The 2009 bathymetric grid of Australia has been produced to include recently acquired datasets, and solutions to issues identified in the previous version. The revised grid has the same extents as its 2005 counterpart, including the Australian water column jurisdiction lying between 92 deg E and 172 deg E, and 8 deg S and 60 deg S. The waters adjacent to the continent of Australia and Tasmania are included, as are areas surrounding Macquarie Island, and the Australian Territories of Norfolk Island, Christmas Island, and Cocos (Keeling) Islands. The area selected does not include Australia's marine jurisdiction offshore from the Territory of Heard and McDonald Islands and the Australian Antarctic Territory. This report details the datasets and procedures used to produce the 2009 bathymetric grid of Australia. As per the 2005 grid, the 0.0025 decimal degree (dd) resolution is only supported where direct bathymetric observations are sufficiently dense (e.g. where swath bathymetry data or digitised chart data exist) (Webster and Petkovic, 2005). In areas where no sounding data are available (in waters off the Australian shelf), the grid is based on the 2 arc minute ETOPO (Smith and Sandwell, 1997) and 1 arc minute ETOPO (Amante and Eakins, 2008) satellite derived bathymetry. The topographic data (on shore data) is based on the revised Australian 0.0025dd topography grid (Geoscience Australia, 2008), the 0.0025dd NZ topography grid (Geographx, 2008) and the 90m SRTM DEM (Jarvis et al, 2008). The final dataset has been provided in ESRI grid and ER Mapper (ers) formats. An associated shapefile has been produced so that the user can identify the input datasets that were used in the final grid. Data Location: This dataset is filed in the eAtlas enduring data repository at: data\other\AU_GA_Bathymetry-2009\derived\AU_e-Atlas-GA_Bathymetry-2009_Contours