This is a metadata record for the Eden offshore wave data buoy (station code WAVEEDN) operated by Manly Hydraulics Laboratory (MHL), NSW Office of Environment and Heritage (OEH). The buoy is moored off Eden at a water depth of approximately 100m. This metadata record includes a down-loadable .pdf summary document which includes a map with numbered deployment locations and a listing of deployment number, location, water depth and deployment period. Data from February 1978 to December 2011 was gathered by the Waverider system developed by the Dutch company, Datawell. The Waverider system uses an accelerometer mounted in a loose tethered buoy (0.7 or 0.9m in diameter) to measure the vertical accelerations of the buoy as it moves with the water surface. The accelerations are integrated twice within the buoy and the displacement signal so obtained is then transmitted to a shore station where it is processed to provide wave data statistics. In December 2011, the station was upgraded with a Datawell Directional Waverider buoy. The Directional Waverider buoy utilises a heave-pitch-roll sensor, two fixed X and Y accelerometers and a three axis fluxgate compass to measure both vertical and horizontal motion. An on-board processor converts the buoy motion to three orthogonal (vertical, north-south, east-west) translation signals that are transmitted to the shore station. The directional spectrum is also routinely transmitted to the receiving station for further processing. This buoy also collects sea surface temperature (SST) data from thermistors that are mounted inside the hull of the buoys, at the base of the buoy about 0.5m below the water surface. The wave and SST data are stored on the receiving station PC before routine transfer to Manly Hydraulics Laboratory via email.

This is a metadata record for the Batemans Bay offshore wave data buoy (station code WAVEBAB) operated by Manly Hydraulics Laboratory (MHL), NSW Office of Environment and Heritage (OEH). The buoy is moored off Batemans Bay at a water depth of approximately 75m. This metadata record includes a down-loadable .pdf summary document which includes a map with numbered deployment locations and a listing of deployment number, location, water depth and deployment period. Data from May 1986 to February 2001 was gathered by the Waverider system developed by the Dutch company, Datawell. The Waverider system uses an accelerometer mounted in a loose tethered buoy (0.7 or 0.9m in diameter) to measure the vertical accelerations of the buoy as it moves with the water surface. The accelerations are integrated twice within the buoy and the displacement signal so obtained is then transmitted to a shore station where it is processed to provide wave data statistics. In February 2001, the station was upgraded with a Datawell Directional Waverider buoy. The Directional Waverider buoy utilises a heave-pitch-roll sensor, two fixed X and Y accelerometers and a three axis fluxgate compass to measure both vertical and horizontal motion. An on-board processor converts the buoy motion to three orthogonal (vertical, north-south, east-west) translation signals that are transmitted to the shore station. The directional spectrum is also routinely transmitted to the receiving station for further processing. This buoy also collects sea surface temperature (SST) data from thermistors that are mounted inside the hull of the buoys, at the base of the buoy about 0.5m below the water surface. The wave and SST data are stored on the receiving station PC before routine transfer to Manly Hydraulics Laboratory via email.

This is a metadata record for the Coffs Harbour offshore wave data buoy (station code WAVECOH) operated by Manly Hydraulics Laboratory (MHL), NSW Office of Environment and Heritage (OEH). The buoy is moored off Coffs Harbour at a water depth of approximately 70m. This metadata record includes a down-loadable .pdf summary document which includes a map with numbered deployment locations and a listing of deployment number, location, water depth and deployment period. Data from May 1976 to February 2012 was gathered by the Waverider system developed by the Dutch company, Datawell. The Waverider system uses an accelerometer mounted in a loose tethered buoy (0.7 or 0.9m in diameter) to measure the vertical accelerations of the buoy as it moves with the water surface. The accelerations are integrated twice within the buoy and the displacement signal so obtained is then transmitted to a shore station where it is processed to provide wave data statistics. In February 2012, the station was upgraded with a Datawell Directional Waverider buoy. The Directional Waverider buoy utilises a heave-pitch-roll sensor, two fixed X and Y accelerometers and a three axis fluxgate compass to measure both vertical and horizontal motion. An on-board processor converts the buoy motion to three orthogonal (vertical, north-south, east-west) translation signals that are transmitted to the shore station. The directional spectrum is also routinely transmitted to the receiving station for further processing. This buoy also collects sea surface temperature (SST) data from thermistors that are mounted inside the hull of the buoys, at the base of the buoy about 0.5m below the water surface. The wave and SST data are stored on the receiving station PC before routine transfer to Manly Hydraulics Laboratory via email.

This is a metadata record for the Sydney offshore wave data buoy (station code WAVESYD) operated by Manly Hydraulics Laboratory (MHL), NSW Office of Environment and Heritage (OEH). The buoy is moored off Sydney at a water depth of approximately 85m. This metadata record includes a down-loadable .pdf summary document which includes a map with numbered deployment locations and a listing of deployment number, location, water depth and deployment period. The Sydney buoy is a direction capable wave-rider buoy made by the Dutch company Datawell. The Directional Waverider buoy utilises a heave-pitch-roll sensor, two fixed X and Y accelerometers and a three axis fluxgate compass to measure both vertical and horizontal motion. An on-board processor converts the buoy motion to three orthogonal (vertical, north-south, east-west) translation signals that are transmitted to the shore station. The directional spectrum is also routinely transmitted to the receiving station for further processing. This buoy also collects sea surface temperature (SST) data from thermistors that are mounted inside the hull of the buoys, at the base of the buoy about 0.5m below the water surface. The wave and SST data are stored on the receiving station PC before routine transfer to Manly Hydraulics Laboratory via email.

This is a metadata record for the Crowdy Head offshore wave data buoy (station code WAVECRH) operated by Manly Hydraulics Laboratory (MHL), NSW Office of Environment and Heritage (OEH). The buoy is moored off Crowdy Head at a water depth of approximately 80m. This metadata record includes a down-loadable .pdf summary document which includes a map with numbered deployment locations and a listing of deployment number, location, water depth and deployment period. Data from October 1985 to August 2011 was gathered by the Waverider system developed by the Dutch company, Datawell. The Waverider system uses an accelerometer mounted in a loose tethered buoy (0.7 or 0.9m in diameter) to measure the vertical accelerations of the buoy as it moves with the water surface. The accelerations are integrated twice within the buoy and the displacement signal so obtained is then transmitted to a shore station where it is processed to provide wave data statistics. In August 2011, the station was upgraded with a Datawell Directional Waverider buoy. The Directional Waverider buoy utilises a heave-pitch-roll sensor, two fixed X and Y accelerometers and a three axis fluxgate compass to measure both vertical and horizontal motion. An on-board processor converts the buoy motion to three orthogonal (vertical, north-south, east-west) translation signals that are transmitted to the shore station. The directional spectrum is also routinely transmitted to the receiving station for further processing. This buoy also collects sea surface temperature (SST) data from thermistors that are mounted inside the hull of the buoys, at the base of the buoy about 0.5m below the water surface. The wave and SST data are stored on the receiving station PC before routine transfer to Manly Hydraulics Laboratory via email.

The Manly Hydraulics Laboratory (MHL) manages and operates the New South Wales coastal environmental data programs. This involves a quality assured, holistic approach to the collection, collation, analysis and delivery of a continuous time series of environmental data. MHL provides specialist services in the area of water, coastal and environmental solutions. MHL is a business unit within the NSW Department of Commerce. MHL has a quality system certified to AS/NZS ISO 9001: 1994-2000. Areas of expertise include: investigation of oceanographic, coastal, estuarine and riverine processes; environmental and water quality studies, data aquisition and field surveys; design and testing of water engineering structures and equipment; and development and operation of physical and numerical models. NHL measures the latest wave height, ocean tides, sea surface temperature, water level, rainfall and barometric pressure off the coast and within NSW. Please note not all data is available online, latest observations only.

The Manly Hydraulics Laboratory (MHL) manages and operates the New South Wales coastal environmental data programs. This involves a quality assured, holistic approach to the collection, collation, analysis and delivery of a continuous time series of environmental data. MHL provides specialist services in the area of water, coastal and environmental solutions. MHL is a business unit within the NSW Department of Commerce. MHL has a quality system certified to AS/NZS ISO 9001: 1994-2000. Areas of expertise include: investigation of oceanographic, coastal, estuarine and riverine processes; environmental and water quality studies, data aquisition and field surveys; design and testing of water engineering structures and equipment; and development and operation of physical and numerical models. MHL measures the latest wave height, ocean tides, sea surface temperature, water level, rainfall and barometric pressure off the coast and within NSW. Please note that not all data is available online, latest observations only.

Tide gauge data collected from pressure tide gauge at Hurd Point, Macquarie Island. Data were collected between 1996-03-07 and 1996-10-27. A temporary tide gauge was installed at Hurd Point as it was suspected that there was a 6 minute wave around the island. The installation was made to determine whether this is correct. Photo Oblique aerial photos showing location of tide gauge, bench mark AUS188 and Hurd Point trig and photo mof GPS set up. Gravity meter set up adjacent tide gauge Temporary Bench Mark Survey Scans of survey field notes showing location of tide gauge in relation to Hurd Point huts, AUS188 and old Auroral Camera stand, vertical differences between AUS188, tide gauge temporary mark and tide gauge housing.

Timeseries data from 'Nelson Lagoon (Outer) Wave Buoy' (nelson-lagoon-outer-wave-buoy)

Timeseries data from 'Naknek Wave Buoy' (naknek-wave-buoy)