Curvature was calculated from the bathymetry surface for each raster cell using the ArcGIS 3D Analyst "Curvature" Tool. Curvature describes the rate of change of curvature (in 1/100 z units) within a square 3x3 cell window. A negative value denotes concavity, while a positive value denotes convexity. The 2x2 meter resolution curvature GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Please see ESRI's online support center for more information about Curvature. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

Plan curvature was calculated from the bathymetry surface for each raster cell using the ArcGIS 3D Analyst "Curvature" Tool. Plan curvature describes the rate of change of curvature (perpendicular to the slope direction) within a square 3x3 cell neighborhood. A negative value denotes concavity, while a positive value denotes convexity. The 2x2 meter resolution plan curvature GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Please see ESRI's online support center for more information about Plan Curvature. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

Slope was calculated from the bathymetry surface for each raster cell using ArcGIS's Spatial Analyst 'Slope' Tool. Slope describes the maximum steepness of a terrain (in degrees) within a square 3x3 cell neighborhood. The 2x2 meter resolution slope GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Please see ESRI's online support center for more information about Slope. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

Slope of slope was calculated from the bathymetry surface for each raster cell by applying the ArcGIS Spatial Analyst 'Slope' Tool to a previously created slope raster. Slope of slope describes the maximum rate of change of slope (in degrees of degrees) within a square 3x3 cell neighborhood. The slope of slope metric has been found to be important in predicting the distribution and abundance of fish and corals (Pittman et al., 2009). Consequently, the 2x2 meter resolution slope of slope GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004;

Rugosity was calculated from the bathymetry surface for each cell using the "Rugosity" function in the Benthic Terrain Modeler toolbox (Jenness 2002, 2004; Wright et al., 2005). Rugosity is defined as the ratio of surface area to planar area within a square 3x3 cell neighborhood. Rugosity values near 1 represent flat, smooth terrain, while higher values reflect increasing rugosity or terrain roughness. The 2x2 meter resolution rugosity GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

Eight complexity surfaces (mean depth, standard deviation of depth, curvature, plan curvature, profile curvature, rugosity, slope, and slope of slope) were stacked and exported to create one image with several different bands (each band representing a specific metric). This image was transformed into its first three principal components using the "Principal Components Analysis" (PCA) function in ENVI 4.6. The transformation reduced the dimensionality of the dataset by removing information that was redundant among the different bands. The resulting 2x2 meter resolution, three band PCA image only contains information that uniquely described the complexity and structure of the seafloor. Coral reef habitat types were delineated and classified from this PCA image. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete

Standard deviation of depth was calculated from the bathymetry surface for each cell using the ArcGIS Spatial Analyst Focal Statistics "STD" parameter. Standard deviation of depth represents the dispersion of depth values (in meters) around the mean depth within a square 3x3 cell window. The 2x2 meter resolution standard deviation of depth GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

This image represents a 2x2 meter resolution bathymetry surface of the moderate-depth portion of the NPS's Virgin Islands Coral Reef National Monument, south of St. John, US Virgin Islands. The depth values contained in this surface are in meters. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

Mean depth was calculated from the bathymetry surface for each cell using the ArcGIS Spatial Analyst Focal Statistics "Mean" parameter. Mean depth represents the average depth value (in meters) within a square 3x3 cell window. The 2x2 meter resolution mean depth GeoTIFF was exported and added as a new map layer to aid in benthic habitat classification. Acoustic imagery was acquired for the VICRNM on two separate missions onboard the NOAA ship, Nancy Foster. The first mission took place from 2/18/04 to 3/5/04. The second mission took place from 2/1/05 to 2/12/05. On both missions, seafloor depths between 14 to 55 m were mapped using a RESON SeaBat 8101 ER (240 kHz) MBES sensor. This pole-mounted system measured water depths across a 150 degree swath consisting of 101 individual 1.5 degree x 1.5 degree beams. The beams to the port and starboard of nadir (i.e., directly underneath the ship) overlapped adjacent survey lines by approximately 10 m. The vessel survey speed was between 5 and 8 kn. In 2004, the ship's location was determined by a Trimble DSM 132 DGPS system, which provided a RTCM differential data stream from the U.S. Coast Guard Continually Operating Reference Station (CORS) at Port Isabel, Puerto Rico. Gyro, heave, pitch and roll correctors were acquired using an Ixsea Octans gyrocompass. In 2005, the ship's positioning and orientation were determined by the Applanix POS/MV 320 V4, which is a GPS aided Inertial Motion Unit (IMU) providing measurements of roll, pitch and heading. The POS/MV obtained its positions from two dual frequency Trimble Zephyr GPS antennae. An auxiliary Trimble DSM 132 DGPS system provided a RTCM differential data stream from the U.S. Coast Guard CORS at Port Isabel, Puerto Rico. For both years, CTD (conductivity, temperature and depth) measurements were taken approximately every 4 hours using a Seabird Electronics SBE-19 to correct for the changing sound velocities in the water column. In 2004, raw data were logged in .xtf (extended triton format) using Triton ISIS software 6.2. In 2005, raw data were logged in .gsf (generic sensor format) using SAIC ISS 2000 software. Data from 2004 were referenced to the WGS84 UTM 20 N horizontal coordinate system, and data from 2005 were referenced to the NAD83 UTM 20 N horizontal coordinate system. Data from both projects were referenced to the Mean Lower Low Water (MLLW) vertical tidal coordinate system. The 2004 and 2005 MBES bathymetric data were both corrected for sensor offsets, latency, roll, pitch, yaw, static draft, the changing speed of sound in the water column and the influence of tides in CARIS Hips & Sips 5.3 and 5.4, respectively. The 2004 data was then binned to create a 1 x 1 m raster surface, and the 2005 data was binned to a create 2 x 2 m raster surface. After these final surfaces were created, the datum for the 2004 bathymetric surfaces was transformed from WGS84 to NAD83 using the "Project Raster" function in ArcGIS 9.1. The 2004 surface was transformed so that it would have the same datum as the 2005 surface. The 2004 bathymetric surface was then down sampled from 1 x 1 to 2 x 2 m using the "Resample" function in ArcGIS 9.1. The 2004 surface was resampled so it would have the same spatial resolution as the 2005 surface. Having the same coordinate systems and spatial resolutions, the final 2004 and 2005 bathymetry rasters were then merged using the Raster Calculator function "Merge" in ArcGIS's Spatial Analyst Extension to create a seamless bathymetry surface for the entire VICRNM area south of St. John. For a complete description of the data acquisition and processing parameters, please see the data acquisition and processing reports (DAPRs) for projects: NF-04-06-VI and NF-05-05-VI (Monaco & Rooney, 2004; Battista & Lazar, 2005).

Benthic habitat maps of the nearshore marine environment of St. John, U.S. Virgin Islands were created by visual interpretation of remotely sensed imagery. The objective of this effort, conducted by NOAA's Center for Coastal Monitoring and Assessment - Biogeography Branch in partnership with the U.S. National Park Service (NPS), was to provide spatially-explicit information on the habitat types, biological cover and live coral cover of St. John's coral reef ecosystem.