The development and generation of the datasets that are published through this data release, were based on the results and findings of the report: Kohn, M.S. and Patton, T.T., 2018, Flood-Inundation Maps for the South Platte River at Fort Morgan, Colorado, 2018: U.S. Geological Survey Scientific Investigations Report 2018-5114, 14 p., https://doi.org/10.3133/sir20185114. The geospatial dataset contain final versions of the raster and vector geospatial data and related metadata. The geospatial data include inundation extents, corresponding inundation depths, and the study area boundaries. Digital flood-inundation maps for a 4.5-mile reach of the South Platte River at Fort Morgan, Colorado from Morgan County Road 16 to Morgan County 20.5, were created by the U.S. Geological Survey (USGS) in cooperation with the Colorado Water Conservation Board. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site (https://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to select water levels (stages) at USGS streamgage 06759500, South Platte River at Fort Morgan. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information are available through the National Water Information System web interface or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (http:/water.weather.gov/ahps/). Water-profiles were computed for the stream reach by means of a one-dimensional, step-backwater model. The September 15, 2013 and May 20, 2017 floods were used to calibrate the model, and the June 15, 2015 and May 29, 2017 floods were used to independently validate the model. Nine pressure transducers were deployed to record the stage at nine different locations along the reach and to document the floods of May 20 and 29, 2017 at the South Platte River at Fort Morgan streamgage. The calibrated hydraulic model was then used to determine 16 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 12 ft (3.66 m) or below bankfull to 27 ft (8.23 m), which is 1 ft (0.3 m) greater than the highest recorded water level (25.73 ft [7.84 m] on September 15, 2013) at the South Platte River at Fort Morgan streamgage during its period of record and the 2013 flood exceeds the major flood stage of 21.5 ft (6.55 m) by more than 4 ft (1.2 m) as defined by the National Weather Service. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging) to delineate the area flooded at stages ranging from 12-ft to 27-ft. The availability of these inundation maps, along with internet information regarding the current stage from the USGS streamgage 06759500, South Platte River at Fort Morgan, Colorado, and forecast river stages from the NWS Advanced Hydrologic Prediction Service, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The development and generation of the datasets that are published in this data release, were based on the methods and findings of the report: Kohn, M.S. and Patton, T.T., 2018, Flood-Inundation Maps for the South Platte River at Fort Morgan, Colorado, 2018: U.S. Geological Survey Scientific Investigations Report 2018-5114, 14 p., https://doi.org/10.3133/sir20185114. The geospatial datasets contain final versions of the raster and vector geospatial data and related metadata, and the model archive dataset contains all relevant files to document and re-run the surface-water hydraulic model that are discussed in the report. Digital flood-inundation maps for a 4.5-mile reach of the South Platte River at Fort Morgan, Colorado from Morgan County Road 16 to Morgan County 20.5, were created by the U.S. Geological Survey (USGS) in cooperation with the Colorado Water Conservation Board. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site (https://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to select water levels (stages) at USGS streamgage 06759500, South Platte River at Fort Morgan. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information are available through the National Water Information System web interface or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (http:/water.weather.gov/ahps/). Water-profiles were computed for the stream reach by means of a one-dimensional, step-backwater model. The September 15, 2013 and May 20, 2017 floods were used to calibrate the model, and the June 15, 2015 and May 29, 2017 floods were used to independently validate the model. Nine pressure transducers were deployed to record the stage at nine different locations along the reach and to document the floods of May 20 and 29, 2017 at the South Platte River at Fort Morgan streamgage. The calibrated hydraulic model was then used to determine 16 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 12 ft (3.66 m) or below bankfull to 27 ft (8.23 m), which is 1 ft (0.3 m) greater than the highest recorded water level (25.73 ft [7.84 m] on September 15, 2013) at the South Platte River at Fort Morgan streamgage during its period of record and the 2013 flood exceeds the major flood stage of 21.5 ft (6.55 m) by more than 4 ft (1.2 m) as defined by the National Weather Service. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging) to delineate the area flooded at stages ranging from 12-ft to 27-ft. The availability of these inundation maps, along with internet information regarding the current stage from the USGS streamgage 06759500, South Platte River at Fort Morgan, Colorado, and forecast river stages from the NWS Advanced Hydrologic Prediction Service, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The development and the generation of the datasets that are published through this data release, were based on the results and findings of the report mentioned here: Kim, M.H., 2018, Flood-inundation maps for the Wabash River at Lafayette, Indiana: U.S. Geological Survey Scientific Investigations Report 2018–5017, 10 p., https://doi.org/10.3133/sir20185017. The geospatial dataset contain final versions of the raster and vector geospatial data and its related metadata, and the model archive dataset contains all relevant files to document and re-run the surface-water (SW) hydraulic model that are discussed in the report.

The development and generation of the datasets that are published in this data release, were based on the methods and findings of the report: Kohn, M.S. and Patton, T.T., 2018, Flood-Inundation Maps for the South Platte River at Fort Morgan, Colorado, 2018: U.S. Geological Survey Scientific Investigations Report 2018-5114, 14 p., https://doi.org/10.3133/sir20185114. The geospatial datasets contain final versions of the raster and vector geospatial data and related metadata, and the model archive dataset contains all relevant files to document and re-run the surface-water hydraulic model that are discussed in the report. Digital flood-inundation maps for a 4.5-mile reach of the South Platte River at Fort Morgan, Colorado from Morgan County Road 16 to Morgan County 20.5, were created by the U.S. Geological Survey (USGS) in cooperation with the Colorado Water Conservation Board. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site (https://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to select water levels (stages) at USGS streamgage 06759500, South Platte River at Fort Morgan. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information are available through the National Water Information System web interface or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (http:/water.weather.gov/ahps/). Water-profiles were computed for the stream reach by means of a one-dimensional, step-backwater model. The September 15, 2013 and May 20, 2017 floods were used to calibrate the model, and the June 15, 2015 and May 29, 2017 floods were used to independently validate the model. Nine pressure transducers were deployed to record the stage at nine different locations along the reach and to document the floods of May 20 and 29, 2017 at the South Platte River at Fort Morgan streamgage. The calibrated hydraulic model was then used to determine 16 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 12 ft (3.66 m) or below bankfull to 27 ft (8.23 m), which is 1 ft (0.3 m) greater than the highest recorded water level (25.73 ft [7.84 m] on September 15, 2013) at the South Platte River at Fort Morgan streamgage during its period of record and the 2013 flood exceeds the major flood stage of 21.5 ft (6.55 m) by more than 4 ft (1.2 m) as defined by the National Weather Service. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging) to delineate the area flooded at stages ranging from 12-ft to 27-ft. The availability of these inundation maps, along with internet information regarding the current stage from the USGS streamgage 06759500, South Platte River at Fort Morgan, Colorado, and forecast river stages from the NWS Advanced Hydrologic Prediction Service, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The development and generation of the datasets that are published in this data release, were based on the methods and findings of the report: Kohn, M.S. and Patton, T.T., 2018, Flood-Inundation Maps for the South Platte River at Fort Morgan, Colorado, 2018: U.S. Geological Survey Scientific Investigations Report 2018-5114, 14 p., https://doi.org/10.3133/sir20185114. The model archive dataset contains all relevant files to document and re-run the surface-water hydraulic model that are discussed in the report. The model archive contains two model runs, the calibration model run and the flood inundation model run. Digital flood-inundation maps for a 4.5-mile reach of the South Platte River at Fort Morgan, Colorado from Morgan County Road 16 to Morgan County 20.5, were created by the U.S. Geological Survey (USGS) in cooperation with the Colorado Water Conservation Board. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site (https://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to select water levels (stages) at USGS streamgage 06759500, South Platte River at Fort Morgan. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information are available through the National Water Information System web interface or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (http:/water.weather.gov/ahps/). Water-profiles were computed for the stream reach by means of a one-dimensional, step-backwater model. The September 15, 2013 and May 20, 2017 floods were used to calibrate the model, and the June 15, 2015 and May 29, 2017 floods were used to independently validate the model. Nine pressure transducers were deployed to record the stage at nine different locations along the reach and to document the floods of May 20 and 29, 2017 at the South Platte River at Fort Morgan streamgage. The calibrated hydraulic model was then used to determine 16 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 12 ft (3.66 m) or below bankfull to 27 ft (8.23 m), which is 1 ft (0.3 m) greater than the highest recorded water level (25.73 ft [7.84 m] on September 15, 2013) at the South Platte River at Fort Morgan streamgage during its period of record and the 2013 flood exceeds the major flood stage of 21.5 ft (6.55 m) by more than 4 ft (1.2 m) as defined by the National Weather Service. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging) to delineate the area flooded at stages ranging from 12-ft to 27-ft. The availability of these inundation maps, along with internet information regarding the current stage from the USGS streamgage 06759500, South Platte River at Fort Morgan, Colorado, and forecast river stages from the NWS Advanced Hydrologic Prediction Service, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The development and generation of the datasets that are published in this data release, were based on the methods and findings of the report: Kohn, M.S. and Patton, T.T., 2018, Flood-Inundation Maps for the South Platte River at Fort Morgan, Colorado, 2018: U.S. Geological Survey Scientific Investigations Report 2018-5114, 14 p., https://doi.org/10.3133/sir20185114. The model archive dataset contains all relevant files to document and re-run the surface-water hydraulic model that are discussed in the report. The model archive contains two model runs, the calibration model run and the flood inundation model run. Digital flood-inundation maps for a 4.5-mile reach of the South Platte River at Fort Morgan, Colorado from Morgan County Road 16 to Morgan County 20.5, were created by the U.S. Geological Survey (USGS) in cooperation with the Colorado Water Conservation Board. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science web site (https://water.usgs.gov/osw/flood_inundation/), depict estimates of the areal extent and depth of flooding corresponding to select water levels (stages) at USGS streamgage 06759500, South Platte River at Fort Morgan. Current conditions for estimating near-real-time areas of inundation using USGS streamgage information are available through the National Water Information System web interface or the National Weather Service (NWS) Advanced Hydrologic Prediction Service (http:/water.weather.gov/ahps/). Water-profiles were computed for the stream reach by means of a one-dimensional, step-backwater model. The September 15, 2013 and May 20, 2017 floods were used to calibrate the model, and the June 15, 2015 and May 29, 2017 floods were used to independently validate the model. Nine pressure transducers were deployed to record the stage at nine different locations along the reach and to document the floods of May 20 and 29, 2017 at the South Platte River at Fort Morgan streamgage. The calibrated hydraulic model was then used to determine 16 water-surface profiles for flood stages at 1-foot intervals referenced to the streamgage datum and ranging from 12 ft (3.66 m) or below bankfull to 27 ft (8.23 m), which is 1 ft (0.3 m) greater than the highest recorded water level (25.73 ft [7.84 m] on September 15, 2013) at the South Platte River at Fort Morgan streamgage during its period of record and the 2013 flood exceeds the major flood stage of 21.5 ft (6.55 m) by more than 4 ft (1.2 m) as defined by the National Weather Service. The simulated water-surface profiles were then combined with a geographic information system digital elevation model (derived from light detection and ranging) to delineate the area flooded at stages ranging from 12-ft to 27-ft. The availability of these inundation maps, along with internet information regarding the current stage from the USGS streamgage 06759500, South Platte River at Fort Morgan, Colorado, and forecast river stages from the NWS Advanced Hydrologic Prediction Service, provides emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post-flood recovery efforts.

The USGS Colorado Water Science Center, in cooperation with the Colorado Water Conservation Board, collected hydraulic data for the South Platte River for areas adjacent to Fort Morgan, Colo., based on the USGS streamgage 06759500 South Platte River at Fort Morgan, CO. The hydraulic data include survey point data for 54 cross sections and 10 pressure transducers, which are used to record the river stage beginning at Morgan County Road 16 and extending downstream to Morgan County Road 20.5 near Fort Morgan, Colo. The cross-section and pressure transducer location data were collected using real-time kinematic Global Navigation Satellite Systems by USGS personnel from February 15, 2017, through April 18, 2017. These data can be used to develop inundation maps, which could be available to emergency personnel, public officials, and the general public using an online public mapping application at the USGS Flood Inundation Mapper website (http://water.usgs.gov/osw/flood_inundation/), which contains flood inundation map libraries from throughout the country created by the USGS.

The USGS Colorado Water Science Center, in cooperation with the Colorado Water Conservation Board, collected hydraulic data for the South Platte River for areas adjacent to Fort Morgan, Colo., based on the USGS streamgage 06759500 South Platte River at Fort Morgan, CO. The hydraulic data include survey point data for 54 cross sections and 10 pressure transducers, which are used to record the river stage beginning at Morgan County Road 16 and extending downstream to Morgan County Road 20.5 near Fort Morgan, Colo. The cross-section and pressure transducer location data were collected using real-time kinematic Global Navigation Satellite Systems by USGS personnel from February 15, 2017, through April 18, 2017. These data can be used to develop inundation maps, which could be available to emergency personnel, public officials, and the general public using an online public mapping application at the USGS Flood Inundation Mapper website (http://water.usgs.gov/osw/flood_inundation/), which contains flood inundation map libraries from throughout the country created by the USGS.

Digital flood-inundation maps for an 8.8-mile reach of the North Platte River, from 1.5 miles upstream of the Highway 92 bridge to 3 miles downstream of the Highway 71 bridge, were created by the U.S. Geological Survey (USGS) in cooperation with the Cities of Scottsbluff and Gering. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Platte River at Scottsbluff, Nebr. (station 06680500). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at https://doi.org/10.5066/F7P55KJN or from the National Weather Service Advanced Hydrologic Prediction Service (site SBRN1) at https://water.weather.gov/ahps2/. Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the current (2018) stage-discharge relation at the Platte River at Scottsbluff, Nebr., streamgage. The hydraulic model was then used to compute 10 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from 9 ft, or near bankfull, to 18 ft, which exceeds the stage that corresponds to the estimated 1-percent annual exceedance probability flood (100-year recurrence interval flood). The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model derived from light detection and ranging data having a 0.6-ft root mean square error and 2-ft horizontal resolution resampled to a 6-ft grid to delineate the area flooded at each water level. The availability of these maps, along with internet information regarding current stage from the USGS streamgage will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post flood recovery efforts.

Digital flood-inundation maps for an 8.8-mile reach of the North Platte River, from 1.5 miles upstream of the Highway 92 bridge to 3 miles downstream of the Highway 71 bridge, were created by the U.S. Geological Survey (USGS) in cooperation with the Cities of Scottsbluff and Gering. The flood-inundation maps, which can be accessed through the USGS Flood Inundation Mapping Science website at http://water.usgs.gov/osw/flood_inundation/, depict estimates of the areal extent and depth of flooding corresponding to selected water levels (stages) at the USGS streamgage on the Platte River at Scottsbluff, Nebr. (station 06680500). Near-real-time stages at this streamgage may be obtained on the Internet from the USGS National Water Information System at https://doi.org/10.5066/F7P55KJN or from the National Weather Service Advanced Hydrologic Prediction Service (site SBRN1) at https://water.weather.gov/ahps2/. Flood profiles were computed for the stream reach by means of a one-dimensional step-backwater model. The model was calibrated by using the current (2018) stage-discharge relation at the Platte River at Scottsbluff, Nebr., streamgage. The hydraulic model was then used to compute 10 water-surface profiles for flood stages at 1-foot (ft) intervals referenced to the streamgage datum and ranging from 9 ft, or near bankfull, to 18 ft, which exceeds the stage that corresponds to the estimated 1-percent annual exceedance probability flood (100-year recurrence interval flood). The simulated water-surface profiles were then combined with a Geographic Information System digital elevation model derived from light detection and ranging data having a 0.6-ft root mean square error and 2-ft horizontal resolution resampled to a 6-ft grid to delineate the area flooded at each water level. The availability of these maps, along with internet information regarding current stage from the USGS streamgage will provide emergency management personnel and residents with information that is critical for flood response activities such as evacuations and road closures, as well as for post flood recovery efforts.