Laboratory slide-hold-slide tests were conducted in a conventional triaxial deformation configuration on 3/4-inch diameter cylindrical cores of Eureka quartzite bisected by a sawcut oriented at 30 degrees from vertical. Tests were conducted at constant normal stresses of 30, 110, and 210 MPa with a 10 MPa pore fluid pressure. The pore fluid was deionized water. Experiments were conducted at temperatures of 22, 100, and 200 degC.

Laboratory slide-hold-slide tests were conducted in a conventional triaxial deformation configuration on 1-inch diameter cylindrical cores of Westerly granite bisected by a sawcut oriented at 30 degrees from vertical. Tests were conducted at a constant confining pressure of 30 MPa with a 10 MPa pore fluid pressure. The pore fluid was deionized water. Experiments were conducted at temperatures of 22, 100, 200, and 250 degC.

Using laboratory slide-hold-slide experiments, at temperatures from 22 to 200 degrees C, to examine effects of fracture reactivation and quasi-static loading on the evolution of fluid transport properties of simulated fractures in Westerly granite. At all temperatures, the in-plane hydraulic transmissivity consistently decays during hold periods resulting in an overall reduction in transmissivity. During the first three to fifteen hours of an experiment, transmissivity decreases rapidly due to the generation of wear products, development of a sliding surface, and compaction of the resulting gouge. Once the sliding surface has developed, the long-term transmissivity decay rate at 22 and 100 degrees C is significantly lower than the transmissivity decay rate during the initial 3-15 hours of the experiment. However, at 200 degrees C, the decay of hydraulic transmissivity remains high throughout the experiment. The long-term decay of hydraulic transmissivity can be fitted with a power law model with more rapid reduction of hydraulic transmissivity at higher temperature. Periods of sliding on the fracture surface result in transient increases in the transmissivity, due to shear dilation, as is expected for Coulomb materials. These transients are superimposed on the long-term decay. When sliding ceases and a new hold period commences, there is a rapid reduction in transmissivity and return to the long-term rate of transmissivity decay. The rate of decay of the transmissivity transients is inversely correlated with temperature, in contrast to the long-term decay and the expected behavior for processes like subcritical crack growth and indentation creep. The higher decay rates that are observed during the initial 3-15 hours of the tests and following sliding, are associated with times that the porosity of the gouge is expected to be high. The difference in decay rates suggests that when the gouge is driven far from equilibrium by active shearing, densification may be dominated by a different mechanism from long-term compaction.

Laboratory slide-hold-slide tests, combined with flow through tests, conducted on Westerly granite with 30 degree sawcut. Tests were conducted with a constant confining pressure of 30 MPa with an average pore pressure of 10 MPa at temperatures of 23 and 200 degC. Three fluid flow conditions were examined (1) no flow, (2) cycled flow, and (3) continuous flow.

Laboratory slide-hold-slide tests were conducted in a conventional triaxial deformation configuration on 1-inch diameter cylindrical cores of Westerly granite bisected by a sawcut oriented at 30 degrees from vertical. Tests were conducted at a constant confining pressure of 30 MPa with a 10 MPa pore fluid pressure. The pore fluid was deionized water. Experiments were conducted at temperatures of 22, 100, 200, and 250 C. This data was collected to examine fault strength recovery in hydrothermal conditions.

This repository contains experimental data from a series of fluid injection-induced shearing tests conducted on Utah FORGE granitoid. The experiments were performed using an aluminum triaxial pressure vessel (TEMCO) apparatus at Pennsylvania State University. The primary aim was to investigate the impact of temperature on fault seismicity and to explore how different pre-stress ratios influence shearing behavior. The data includes results from experiments conducted under varying conditions of temperature, pre-stress ratios, and pore pressure increments. The rock samples used in these experiments were 60-grit granitoid with a single inclined fracture oriented at 60 degrees with respect to the horizontal cross-section. The dataset also includes measurements of normal stiffness at different temperatures and images of the experimental apparatus. The included README file details each experiential setup and outlines which data files represent which experimental conditions.

This repository contains experimental data from a series of fluid injection-induced shearing tests conducted on Utah FORGE granitoid. The experiments were performed using an aluminum triaxial pressure vessel (TEMCO) apparatus at Pennsylvania State University. The primary aim was to investigate the impact of temperature on fault seismicity and to explore how different pre-stress ratios influence shearing behavior. The data includes results from experiments conducted under varying conditions of temperature, pre-stress ratios, and pore pressure increments. The rock samples used in these experiments were 60-grit granitoid with a single inclined fracture oriented at 60 degrees with respect to the horizontal cross-section. The dataset also includes measurements of normal stiffness at different temperatures and images of the experimental apparatus. The included README file details each experiential setup and outlines which data files represent which experimental conditions.

Using laboratory slide-hold-slide experiments, at temperatures from 22 to 200 degrees C, to examine effects of fracture reactivation and quasi-static loading on the evolution of fluid transport properties of simulated fractures in Westerly granite. At all temperatures, the in-plane hydraulic transmissivity consistently decays during hold periods resulting in an overall reduction in transmissivity. During the first three to fifteen hours of an experiment, transmissivity decreases rapidly due to the generation of wear products, development of a sliding surface, and compaction of the resulting gouge. Once the sliding surface has developed, the long-term transmissivity decay rate at 22 and 100 degrees C is significantly lower than the transmissivity decay rate during the initial 3-15 hours of the experiment. However, at 200 degrees C, the decay of hydraulic transmissivity remains high throughout the experiment. The long-term decay of hydraulic transmissivity can be fitted with a power law model with more rapid reduction of hydraulic transmissivity at higher temperature. Periods of sliding on the fracture surface result in transient increases in the transmissivity, due to shear dilation, as is expected for Coulomb materials. These transients are superimposed on the long-term decay. When sliding ceases and a new hold period commences, there is a rapid reduction in transmissivity and return to the long-term rate of transmissivity decay. The rate of decay of the transmissivity transients is inversely correlated with temperature, in contrast to the long-term decay and the expected behavior for processes like subcritical crack growth and indentation creep. The higher decay rates that are observed during the initial 3-15 hours of the tests and following sliding, are associated with times that the porosity of the gouge is expected to be high. The difference in decay rates suggests that when the gouge is driven far from equilibrium by active shearing, densification may be dominated by a different mechanism from long-term compaction.

This dataset contains results from four fluid injection experiments at 24 C, 69 C, 111 C, and 140 C using a triaxial loading apparatus ("Temco"). Tests were conducted on a Utah FORGE granite sample with a 30 degree inclined fracture. Confining pressure was maintained at 10 MPa, while shear stress was reduced to create a zero-displacement condition, which means the shear stress decreases continuously. Pore pressure was increased stepwise at 300 kPa every six minutes to simulate injection. Temperature was rapidly raised by voltage heating and then stabilized. Data are provided in spreadsheet format, with one file per temperature. Each file contains upstream and downstream measurement sheets with columns for pressure, flow rate, displacement, and time, with units specified in the headers.