Clearwater Lake, on the Black River near Piedmont in Reynolds County, Missouri, was constructed in 1948 and is operated by the U.S. Army Corps of Engineers for flood-risk reduction, recreation, and fish and wildlife habitat. The lake area is about 1,800 acres with about 34 miles of shoreline at the conservation pool elevation of 498 feet. Periodically, many lakes operated by the U.S. Army Corps of Engineers have bathymetric and sediment surveys to monitor the status of the lake. In May 2017, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, surveyed the bathymetry of Clearwater Lake to prepare an updated bathymetric map and surface area and capacity table. A previous survey completed in 2008 was contrasted with the 2017 survey to document the changes in the bathymetric surface of the lake. Data sets included are the bathymetric data points collected during the 2017 bathymetric survey. There are two data sets included: the multibeam data (averaged to 3.28 feet) that was used as the source of points to create the bathymetric surface and the raw multibeam data from 4 selected resurvey areas that was used as quality assurance data to test the accuracy of the 3.28-feet spacing data points. Richards, J.M., and Huizinga, R.J., 2018, Bathymetric contour map, surface area and capacity table, and bathymetric difference map for Clearwater Lake near Piedmont, Missouri, 2017: U.S. Geological Survey Scientific Investigations Map 3409, 1 sheet, https://doi.org/10.3133/sim3409.

The U.S. Geological Survey (USGS) in cooperation with the Little Rock District, U.S. Army Corps of Engineers conducted a bathymetric survey of the Black River from Clearwater Lake Dam near Piedmont, Missouri, to southern Butler County, Missouri, from June 16-19, 2020, and from June 22-24, 2020. One hundred and eight sites were surveyed at pre-established transect locations along a 45-mile reach at distances spaced from about 0.3 to 2 miles apart. River-channel cross sections were surveyed to determine water depths along each transect using an acoustic Doppler current profiler (ADCP). Positional location of the water-depth locations was obtained from a global positioning system receiver onboard the ADCP. Water-surface elevation at the water-depth locations was computed using vertical control points collected at the location of the cross sections with survey-grade Global Navigation Satellite Systems (GNSS) equipment. Standard methods of practice (Rydlund and Densmore, 2012) were used while obtaining the GNSS control points. Channel cross-section point elevations were obtained by subtracting the water depths along the cross-section transect from the water-surface elevation at the location of the transect. Positional location is reported in World Geodetic System 1984 geographic decimal degree coordinates. Depth is reported in meters and bathymetric elevation is referenced to the North American Vertical Datum of 1988. These data are provided in the Environmental Systems Research Institute (ESRI) shapefile format consisting of a group of files that have been compressed into a zip archive that is named black_river_survey_shapefile.zip. References Rydlund, P.H., Jr., and Densmore, B.K., 2012, Methods of practice and guidelines for using survey-grade global navigation satellite systems (GNSS) to establish vertical datum in the United States Geological Survey: U.S. Geological Survey Techniques and Methods, book 11, chap. D1, 102 p. with appendixes.

Water supply lakes are the primary source of water for many communities in northern and western Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water supply. Many of the water supply lakes in Missouri were previously surveyed by the U.S. Geological Survey (USGS) in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. In April and May 2022, the USGS, in cooperation with the Missouri Department of Natural Resources (MoDNR) and in collaboration with the cities of Cameron, Springfield, and Unionville, Missouri, completed bathymetric surveys of seven (7) lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At some lakes, supplemental data were collected in shallow areas using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary bench marks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the surveys are provided in ESRI Shapefile format (ESRI, 2023). Each of the seven lakes surveyed in 2022 has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. The zip files follow the format of "####2022_bathy_pts.zip" or ####2022_QA_raw.zip," where "####" is the lake name. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of the metadata file. The various reference marks and additional points from all the lake surveys are provided in ESRI Shapefile format (ESRI, 2023) with an attribute table on the main landing page. Attribute/column labels of this table are described in the "Entity and attribute" section of the metadata file. References Cited: Environmental Systems Research Institute, 2023, ArcGIS: accessed July 12, 2023, at https://www.esri.com/en-us/arcgis/about-arcgis/overview Huizinga, R.J., 2014, Bathymetric surveys and area/capacity tables of water-supply reservoirs for the city of Cameron, Missouri, July 2013: U.S. Geological Survey Open-File Report 2014–1005, 15 p.,

Water supply lakes are the primary source of water for many communities in northern and western Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water supply. Many of the water supply lakes in Missouri were previously surveyed by the U.S. Geological Survey (USGS) in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. In April and May 2022, the USGS, in cooperation with the Missouri Department of Natural Resources (MoDNR) and in collaboration with the cities of Cameron, Springfield, and Unionville, Missouri, completed bathymetric surveys of seven (7) lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At some lakes, supplemental data were collected in shallow areas using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary bench marks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the surveys are provided in ESRI Shapefile format (ESRI, 2023). Each of the seven lakes surveyed in 2022 has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. The zip files follow the format of "####2022_bathy_pts.zip" or ####2022_QA_raw.zip," where "####" is the lake name. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of the metadata file. The various reference marks and additional points from all the lake surveys are provided in ESRI Shapefile format (ESRI, 2023) with an attribute table on the main landing page. Attribute/column labels of this table are described in the "Entity and attribute" section of the metadata file. References Cited: Environmental Systems Research Institute, 2023, ArcGIS: accessed July 12, 2023, at https://www.esri.com/en-us/arcgis/about-arcgis/overview Huizinga, R.J., 2014, Bathymetric surveys and area/capacity tables of water-supply reservoirs for the city of Cameron, Missouri, July 2013: U.S. Geological Survey Open-File Report 2014–1005, 15 p.,

Water-supply lakes are the primary source of water for many communities throughout Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water-supply. Many of the water-supply lakes in Missouri were previously surveyed by the U.S. Geological Survey (USGS) in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. In April and May 2023, the USGS, in cooperation with the Missouri Department of Natural Resources (MoDNR) and in collaboration with the cities of Adrian, Ironton, Unity Village, and Vandalia, Missouri, completed bathymetric surveys of six (6) lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At Adrian, supplemental data were collected in a shallow upper reservoir using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary benchmarks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the surveys are provided in ESRI Shapefile format (ESRI, 2023). Each of the six lakes surveyed in 2023 has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. The zip files follow the format of "####2023_bathy_pts.zip" or ####2023_QA_raw.zip," where "####" is the lake name. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of the associated metadata file. The various reference marks and additional points from all the lake surveys are provided in ESRI Shapefile format (ESRI, 2023) with an attribute table on the main landing page. Attribute/column labels of this table are described in the "Entity and attribute" section of the associated metadata file. References Cited: Environmental Systems Research Institute, 2023, ArcGIS: accessed July 12, 2023, at https://www.esri.com/en-us/arcgis/about-arcgis/overview. Huizinga, R.J., 2014, Bathymetric surveys and area/capacity tables of water-supply reservoirs for the city of Cameron, Missouri, July 2013: U.S. Geological Survey Open-File Report

Water-supply lakes are the primary source of water for many communities throughout Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water-supply. Many of the water-supply lakes in Missouri were previously surveyed by the U.S. Geological Survey (USGS) in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. In April and May 2023, the USGS, in cooperation with the Missouri Department of Natural Resources (MoDNR) and in collaboration with the cities of Adrian, Ironton, Unity Village, and Vandalia, Missouri, completed bathymetric surveys of six (6) lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At Adrian, supplemental data were collected in a shallow upper reservoir using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary benchmarks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the surveys are provided in ESRI Shapefile format (ESRI, 2023). Each of the six lakes surveyed in 2023 has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. The zip files follow the format of "####2023_bathy_pts.zip" or ####2023_QA_raw.zip," where "####" is the lake name. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of the associated metadata file. The various reference marks and additional points from all the lake surveys are provided in ESRI Shapefile format (ESRI, 2023) with an attribute table on the main landing page. Attribute/column labels of this table are described in the "Entity and attribute" section of the associated metadata file. References Cited: Environmental Systems Research Institute, 2023, ArcGIS: accessed July 12, 2023, at https://www.esri.com/en-us/arcgis/about-arcgis/overview. Huizinga, R.J., 2014, Bathymetric surveys and area/capacity tables of water-supply reservoirs for the city of Cameron, Missouri, July 2013: U.S. Geological Survey Open-File Report

Water supply lakes are the primary source of water for many communities in northern and western Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water supply. Many of the water supply lakes in Missouri were previously surveyed by the U.S. Geological Survey in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. From July 2019 to June 2020, the U.S. Geological Survey, in cooperation with the Missouri Department of Natural Resources and various cities in northwestern Missouri, completed bathymetric surveys of twelve (12) lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At some lakes, supplemental data were collected in shallow areas using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary bench marks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. Bethany New Lake was resurveyed in March 2020 because the original data collected in July 2019 were found to have corrupted position data. Mozingo Lake and Maryville Reservoir were surveyed in June 2020 as part of the group of lakes surveyed in 2020. However, extraordinary interest in the bathymetry at Mozingo Lake by the city of Maryville necessitated these data being released earlier than the other 2020 lakes. The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the surveys are provided in ESRI Shapefile format (ESRI, 2021). Each of the 10 lakes surveyed in 2019 has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. Data from the surveys at Mozingo Lake and Maryville Reservoir in 2020 are in four zip files on a single child page, one for the bathymetric data and one for the bathymetric quality assurance data for each of the two lakes, and a single summary metadata file. The zip files follow the format of "####YYYY_bathy_pts.zip" or ####YYYY_QA_raw.zip", where "####" is the lake name, and "YYYY" is the survey year. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of

Water supply lakes are the primary source of water for many communities in northern and western Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water supply. Many of the water supply lakes in Missouri were previously surveyed by the U.S. Geological Survey in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. From July 2019 to June 2020, the U.S. Geological Survey, in cooperation with the Missouri Department of Natural Resources and various cities in northwestern Missouri, completed bathymetric surveys of twelve (12) lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At some lakes, supplemental data were collected in shallow areas using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary bench marks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. Bethany New Lake was resurveyed in March 2020 because the original data collected in July 2019 were found to have corrupted position data. Mozingo Lake and Maryville Reservoir were surveyed in June 2020 as part of the group of lakes surveyed in 2020. However, extraordinary interest in the bathymetry at Mozingo Lake by the city of Maryville necessitated these data being released earlier than the other 2020 lakes. The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the surveys are provided in ESRI Shapefile format (ESRI, 2021). Each of the 10 lakes surveyed in 2019 has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. Data from the surveys at Mozingo Lake and Maryville Reservoir in 2020 are in four zip files on a single child page, one for the bathymetric data and one for the bathymetric quality assurance data for each of the two lakes, and a single summary metadata file. The zip files follow the format of "####YYYY_bathy_pts.zip" or ####YYYY_QA_raw.zip", where "####" is the lake name, and "YYYY" is the survey year. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of

Bathymetry data were collected during a July 2019 SWATHPlus survey of Ozette Lake, Washington. Data were collected and processed by the the U.S. Geological Survey (USGS), Pacific Coastal and Marine Science Center (PCMSC) with fieldwork activity number 2019-622-FA. The 2-m bathymetry data are provided as a GeoTIFF image.

Water supply lakes are the primary source of water for many communities in northern and western Missouri. Therefore, accurate and up-to-date estimates of lake capacity are important for managing and predicting adequate water supply. Many of the water supply lakes in Missouri were previously surveyed by the U.S. Geological Survey in the early 2000s (Richards, 2013) and in 2013 (Huizinga, 2014); however, years of potential sedimentation may have resulted in reduced water storage capacity. Periodic bathymetric surveys are useful to update the area/capacity table and to determine changes in the bathymetric surface. In June and July 2020, the U.S. Geological Survey, in cooperation with the Missouri Department of Natural Resources and in collaboration with various cities in north- and west-central Missouri, completed bathymetric surveys of 12 lakes using a marine-based mobile mapping unit, which consists of a multibeam echosounder (MBES) and an inertial navigation system (INS) mounted on a marine survey vessel. Bathymetric data were collected as the vessel traversed longitudinal transects to provide nearly complete coverage of the lake. The MBES was electronically tilted in some areas to improve data collection along the shoreline, in coves, and in areas that are shallower than about 2.0 meters deep (the practical limit of reasonable and safe data collection with the MBES). At some lakes, supplemental data were collected in shallow areas using an acoustic Doppler current profiler (ADCP) mounted on a remote-controlled vessel equipped with a differential global positioning system (DGPS). Bathymetric quality-assurance data also were collected at each lake to evaluate the vertical accuracy of the gridded bathymetric point data from the MBES. As part of the survey at each of these lakes, one or more reference marks or temporary bench marks were established to provide a point of known location and elevation from which the water surface could be measured or another survey could be referenced at a later date. In addition, the elevation of a primary spillway or intake was surveyed, when present. These points were surveyed using a real-time kinematic (RTK) Global Navigation Satellite System (GNSS) receiver connected to the Missouri Department of Transportation real-time network (RTN), which provided real-time survey-grade horizontal and vertical positioning, using field procedures as described in Rydlund and Densmore (2012) for a Level II real-time positioning survey. Mozingo Lake and Maryville Reservoir were surveyed in June 2020 as part of the group of lakes surveyed in 2020. However, extraordinary interest in the bathymetry at Mozingo Lake by the city of Maryville necessitated these data being released earlier than the other 2020 lakes (Huizinga and others, 2021, 2022). The MBES data can be combined with light detection and ranging (lidar) data to prepare a bathymetric map and a surface area and capacity table for each lake. These data also can be used to compare the current bathymetric surface with any previous bathymetric surface. Data from each of the remaining 10 lakes surveyed in 2020 are provided in ESRI Shapefile format (ESRI, 2021). Each of the lakes surveyed in 2020 except Higginsville has a child page containing the metadata and two zip files, one for the bathymetric data, and the other for the bathymetric quality-assurance data. Data from the surveys at the Upper and Lower Higginsville Reservoirs are in two zip files on a single child page, one for the bathymetric data and one for the bathymetric quality assurance data of both lakes, and a single summary metadata file. The zip files follow the format of "####2020_bathy_pts.zip" or "####2020_QA_raw.zip," where "####" is the lake name. Each of these zip files contains a shapefile with an attribute table. Attribute/column labels of each table are described in the "Entity and attribute" section of the metadata file. The various reference marks and additional points from all the lake