데이터셋 상세
미국
EGS Collab Experiment 2: Continuous Broadband Seismic Waveform Data
Two broadband seismometers were installed on the 4100 level and recorded for the duration of EGS Collab Experiment #2. Inspired by published data from similar instruments installed in the Aspo Hard Rock Lab, these long-period instruments aimed to measure the tilting of the drift in response to the injection of fluid into the testbed. One instrument was installed underneath the wellheads in Site A (aka the "battery" alcove) and the other was installed along the east wall of the drift, south of Site B. Due to the feet of gravel (ballast) laid along the floor of the drift, we were unable to anchor the sensors directly to the rock. As a result, the coupling of the sensors to the experiment rock volume is likely poor. In addition, there are a number of noise sources that complicate the interpretation of the data. For example, sensor BBB is installed adjacent (within 3 ft) to the rail line that runs towards the Ross shaft. Trains (motors) run along this line almost daily and produce a large signal in these data. Careful extraction of periods of interest, as well as filtering for specific signals, is necessary. The sensors are Nanometrics Trillium Compact Posthole seismometers, sensitive down to 120 seconds period. They were installed as close to the drift wall and as deep as we could manually excavate (only about 1 ft or so). The holes were leveled with sand and the sensors were placed on a paver before backfilling with sand. The hole was then covered by a bucket filled with insulation to improve the sensor's isolation from daily temperature variations, which are minor but present due to drift ventilation from the surface. Data were recorded on Nanometrics Centaur digitizers at 100 Hz. The full response information is available in the StationXML file provided here, or by querying the sensors through the IRIS DMC (see links below). These instruments were provided free of charge through the IRIS PASSCAL instrument center. The network code is XP and the station codes are BBA and BBB. The waveform data can be queried through the IRIS FDSN server using any method the user likes. One convenient option is to use the Obspy python package: https://docs.obspy.org/packages/obspy.clients.fdsn.html
데이터 정보
연관 데이터
EGS Collab Experiment 1: Continuous Active-Source Seismic Monitoring (CASSM) Data
공공데이터포털
The U.S. Department of Energy's Enhanced Geothermal System (EGS) Collab project aims to improve our understanding of hydraulic stimulations in crystalline rock for enhanced geothermal energy production through execution of intensely monitored meso-scale experiments. The first experiment was performed at the 4850 ft level of the Sanford Underground Research Facility (SURF), approximately 1.5 km below the surface at Lead, South Dakota. The data reported here were collected by the continuous active-source seismic monitoring (CASSM) system (Ajo-Franklin et al., 2011). This system was permanently installed in the testbed and consisted of 17 piezoelectric sources that were recorded by 2-12 channel hydrophone arrays, 18 3-C accelerometers, and 4 3-C geophones at a Nyquist frequency of 24kHz. The source array was activated in a repeated sequence of shots (each source fired 16 times and stacked into resultant waveforms) for the duration of the experiment (April 25, 2018 - March 7, 2019) with few exceptions. Please see the attached documents describing the source / receiver geometry. The data are available in both seg2 (.dat extension) and segy (.sgy extension) format. Each segy file contains multiple seg2 files.
EGS Collab Experiment 1: Baseline Cross-well Seismic
공공데이터포털
As part of the geophysical characterization suite for the first EGS Collab tesbed, here are the baseline cross-well seismic data and resultant models. The campaign seismic data have been organized, concatenated with geometry and compressional (P-) & and shear (S-) wave picks, and submitted as SGY files. P-wave data were collected and analyzed in both 2D and 3D, while S-wave data were collected and analyzed in 2D only. Inversion models are provided as point volumes; the volumes have been culled to include only the points within source/receiver array coverage. The full models space volumes are also included, if relevant. An AGU 2018 poster by Linneman et al. is included that provides visualizations/descriptions of the cross-well seismic characterization method, elastic moduli calculations, and images of model inversion results.
EGS Collab Experiment 2: Earth Model Datasets
공공데이터포털
The EGS Collab Project performed a series of tests to increase the understanding the response of crystalline rock mass to stimulations and fluid circulation to efficiently implement enhanced geothermal systems (EGS) technologies. The EGS Collab team created two underground testbeds at the Sanford Underground Research Facility (SURF) in Lead SD at a depth of approximately 1.5 km (4850 level) and 1.25 km (4100 level) to examine hydraulic fracturing and hydraulic shearing, respectively. Experiment 2 was designed to examine hydraulic shearing and fluid flow in testbed 2 in amphibolite under a controlled set of stress and fracture conditions. This document summarizes the general geology, natural fractures, and conceptual model(s) of stimulated fracture networks in the testbed 2. The dataset package included here are input and output products associated with Earth Models for the EGS Collab Testbed 2. The earth model datasets are included in the whole package (project) in Leapfrog file format. Also, datasets are given in primary input file format (csv).
EGS Collab Experiment 2: Wireline Geophysical Well Logs
공공데이터포털
This is the full wireline geophysical datasets for characterization of the EGS Collab Experiment #2 testbed. A metadata fill is included within the dataset explaining the logs, fracture picks, etc. Eleven boreholes were drilled for this testbed and each one was logged with north seeking gyro, optical televiewer, acoustic televiewer, fluid temperature conductivity, resistivity and gamma, and full waveform sonic. In these folders are the processed results as text, csv and pdf files along with the raw data which will need to be read by WellCAD.
목록