TL2MTLN_8 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Methanol Nadir Version 8 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contain retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits.Nadir observations, which point directly to the surface of the Earth, are different from limb observations, which are pointed at various off-nadir angles into the atmosphere. Nadir and limb observations were added to separate L2 files, and a single ancillary file was composed of data that are common to both nadir and limb files. A Nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals were performed. Each observation was the input for retrievals of species Volume Mixing Ratios (VMRs), temperature profiles, surface temperature, and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels, representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging was employed. Also, missing or bad retrievals were not reported. Further, observations were occasionally scheduled on non-global survey days. In general they were measurements made for validation purposes or with highly focused science objectives. Those non-global survey measurements were referred to as “special observations.”A Limb sequence within the TES Global Survey was three high-resolution scans over the same limb locations. The Limb standard product consists of four files, where each file is composed of the Global Survey Limb observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Limb observations used a repeating sequence of filter wheel positions. Special Observations could only be scheduled during the 9 or 10 orbit gaps in the Global Surveys, and were conducted in any of three basic modes: stare, transect, step-and-stare. The mode used depended on the science requirement. Each limb observation Limb 1, Limb 2 and Limb 3, were processed independently. Thus, each limb standard product consisted of three sets where each set consisted of 1,152 observations. For TES, the swath object represented one of these sets. Thus, each limb standard product consisted of three swath objects, one for each observation, Limb 1, Limb 2, and Limb 3. The

TL2MTLNS_8 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Methanol Nadir Special Observation Version 8 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contains retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits.A nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consisted of four files, where each file was composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals were performed. Each observation was the input for retrievals of species volume mixing ratios (VMRs), temperature profiles, surface temperature and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging is employed. Also, missing or bad retrievals were not reported. The organization of data within the Swath object was based on a superset of the Upper Atmosphere Research Satellite (UARS) pressure levels that was used to report concentrations of trace atmospheric gases. The reporting grid was the same pressure grid used for modeling. There were 67 reporting levels from 1211.53 hPa, which allowed for very high surface pressure conditions, to 0.1 hPa, about 65 km. In addition, the products reported values directly at the surface when possible or at the observed cloud top level. Thus in the Standard Product files each observation could have potentially contained estimates for the concentration of a particular molecule at 67 different pressure levels within the atmosphere. However, for most retrieved profiles, the highest pressure levels were not observed due to a surface at lower pressure or cloud obscuration. For pressure levels corresponding to altitudes below the cloud top or surface, where measurements were not possible, a fill value was applied.To minimize the duplication of information between the individual species standard products, data fields common to each species (such as spacecraft coordinates, emissivity, and other data fields) have been collected into a separate standard product, termed the TES L2 Ancillary Data product (ESDT short name: TL2ANC). Users of this product should also obtain the Ancillary Data product.

TL2CH4LN_7 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Methane Lite Nadir Version 7 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contain retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits. Nadir and limb observations were in separate L2 files, and a single ancillary file was composed of data that was common to both nadir and limb files.Nadir observations, which point directly to the surface of the Earth, are different from limb observations, which are pointed at various off-nadir angles into the atmosphere. Nadir and limb observations were added to separate L2 files, and a single ancillary file was composed of data that are common to both nadir and limb files. A Nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 4,608 retrievals were performed. Each observation was the input for retrievals of species Volume Mixing Ratios (VMRs), temperature profiles, surface temperature, and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels, representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging was employed. Also, missing or bad retrievals were not reported. Further, observations were occasionally scheduled on non-global survey days. In general they were measurements made for validation purposes or with highly focused science objectives. Those non-global survey measurements were referred to as “special observations.”A Limb sequence within the TES Global Survey was three high-resolution scans over the same limb locations. The Limb standard product consists of four files, where each file is composed of the Global Survey Limb observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Limb observations used a repeating sequence of filter wheel positions. Special Observations could only be scheduled during the 9 or 10 orbit gaps in the Global Surveys, and were conducted in any of three basic modes: stare, transect, step-and-stare. The mode used depended on the science requirement. Each limb observation Limb 1, Limb 2 and Limb 3, were processed independently. Thus, each limb standard product consisted of three sets where each set consisted of 1,152 observations. For TES, the swath object

TL2CH4N_8 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Methane Nadir Version 8 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contain retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits.Nadir observations, which point directly to the surface of the Earth, are different from limb observations, which are pointed at various off-nadir angles into the atmosphere. Nadir and limb observations were added to separate L2 files, and a single ancillary file was composed of data that are common to both nadir and limb files. A Nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals were performed. Each observation was the input for retrievals of species Volume Mixing Ratios (VMRs), temperature profiles, surface temperature, and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging was employed. Also, missing or bad retrievals were not reported. Further, observations were occasionally scheduled on non-global survey days. In general they were measurements made for validation purposes or with highly focused science objectives. Those non-global survey measurements were referred to as “special observations”The organization of data within the Swath object was based on a superset of the Upper Atmosphere Research Satellite (UARS) pressure levels used to report concentrations of trace atmospheric gases. The reporting grid was the same pressure grid used for modeling. There were 67 reporting levels from 1211.53 hPa, which allowed for very high surface pressure conditions, to 0.1 hPa, about 65 km. In addition, the products reported values directly at the surface when possible or at the observed cloud top level. Thus in the Standard Product files, each observation could potentially contain estimates for the concentration of a particular molecule at 67 different pressure levels within the atmosphere. However, for most retrieved profiles, the highest pressure levels were not observed due to a surface at lower pressure or cloud obscuration. For pressure levels corresponding to altitudes below the cloud top or surface, where measurements were not possible, a fill value was applied.To

TL2H2ON_8 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Water Vapor Nadir Version 8 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contains retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits. A nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consists of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals were performed. Each observation was the input for retrievals of species volume mixing ratios (VMRs), temperature profiles, surface temperature and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object wa bounded by the number of observations in a global survey and a predefined set of pressure levels representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging is employed. Also, missing or bad retrievals were not reported. The organization of data within the Swath object was based on a superset of the Upper Atmosphere Research Satellite (UARS) pressure levels that was used to report concentrations of trace atmospheric gases. The reporting grid was the same pressure grid used for modeling. There were 67 reporting levels from 1211.53 hPa, which allowed for very high surface pressure conditions, to 0.1 hPa, about 65 km. In addition, the products reported values directly at the surface when possible or at the observed cloud top level. Thus in the Standard Product files each observation could potentially contain estimates for the concentration of a particular molecule at 67 different pressure levels within the atmosphere. However, for most retrieved profiles, the highest pressure levels were not observed due to a surface at lower pressure or cloud obscuration. For pressure levels corresponding to altitudes below the cloud top or surface, where measurements were not possible, a fill value was applied.To minimize the duplication of information between the individual species standard products, data fields common to each species (such as spacecraft coordinates, emissivity, and other data fields) have been collected into a separate standard product, termed the TES L2 Ancillary Data product (ESDT short name: TL2ANC). Users of this product should also obtain the Ancillary Data product.

TL2NH3N_8 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Ammonia Nadir Version 8 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contained retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits.A nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consisted of four files, where each file was composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals were performed. Each observation was the input for retrievals of species volume mixing ratios (VMRs), temperature profiles, surface temperature and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging is employed. Also, missing or bad retrievals were not reported. The organization of data within the Swath object was based on a superset of the Upper Atmosphere Research Satellite (UARS) pressure levels that was used to report concentrations of trace atmospheric gases. The reporting grid was the same pressure grid used for modeling. There were 67 reporting levels from 1211.53 hPa, which allowed for very high surface pressure conditions, to 0.1 hPa, about 65 km. In addition, the products reported values directly at the surface when possible or at the observed cloud top level. Thus in the Standard Product files each observation could have potentially contained estimates for the concentration of a particular molecule at 67 different pressure levels within the atmosphere. However, for most retrieved profiles, the highest pressure levels were not observed due to a surface at lower pressure or cloud obscuration. For pressure levels corresponding to altitudes below the cloud top or surface, where measurements were not possible, a fill value was applied.To minimize the duplication of information between the individual species standard products, data fields common to each species (such as spacecraft coordinates, emissivity, and other data fields) have been collected into a separate standard product, termed the TES L2 Ancillary Data product (ESDT short name: TL2ANC). Users of this product should also obtain the Ancillary Data product.

TL2O3LN_7 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Ozone Lite Nadir Version 7 data product. TES Level 2 data contain retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) are also provided. L2 modeled spectra are evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compares observed spectra to the modeled spectra and iteratively updates the atmospheric parameters. L2 standard product files include information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consists of a maximum of 16 consecutive orbits.A nadir sequence within the TES Global Survey is a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations currently only use a single set of filter mix. A Global Survey consists of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals are performed. Each observation is the input for retrievals of species Volume Mixing Ratios (VMR), temperature profiles, surface temperature and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density and other diagnostic quantities. Each TES Level 2 standard product reports information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object is bounded by the number of observations in a global survey and a predefined set of pressure levels representing slices through the atmosphere. Each standard product can have a variable number of observations depending upon the Global Survey configuration and whether averaging is employed. Also, missing or bad retrievals are not reported. The organization of data within the Swath object is based on a superset of the UARS pressure levels used to report concentrations of trace atmospheric gases. The reporting grid is the same pressure grid used for modeling. There are 67 reporting levels from 1211.53 hPa, which allows for very high surface pressure conditions, to 0.1 hPa, about 65 km. In addition, the products will report values directly at the surface when possible or at the observed cloud top level. Thus, in the Standard Product files each observation can potentially contain estimates for the concentration of a particular molecule at 67 different pressure levels within the atmosphere. However, for most retrieved profiles, the highest pressure levels are not observed due to a surface at lower pressure or cloud obscuration. For pressure levels corresponding to altitudes below the cloud top or surface, where measurements were not possible, a fill value will be applied.To minimize the duplication of information between the individual species standard products, data fields common to each species (such as spacecraft coordinates, emissivity, and other data fields) have been collected into a separate standard product, termed the TES L2 Ancillary Data product (ESDT short name: TL2ANC). Users of this product should also obtain the Ancillary Data product.

TL2NH3LN_7 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Ammonia Lite Nadir Version 7 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contain retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits. Nadir observations, which point directly to the surface of the Earth are different from limb observations, which are pointed at various off-nadir angles into the atmosphere. Nadir and limb observations were added to separate L2 files, and a single ancillary file was composed of data that are common to both nadir and limb files. A Nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 3,200 retrievals were performed. Each observation was the input for retrievals of species Volume Mixing Ratios (VMRs), temperature profiles, surface temperature, and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging was employed. Also, missing or bad retrievals were not reported. Further, observations were occasionally scheduled on non-global survey days. In general they were measurements made for validation purposes or with highly focused science objectives. Those non-global survey measurements were referred to as “special observations”The organization of data within the Swath object was based on a superset of the Upper Atmosphere Research Satellite (UARS) pressure levels used to report concentrations of trace atmospheric gases. The reporting grid was the same pressure grid used for modeling. There were 67 reporting levels from 1211.53 hPa, which allowed for very high surface pressure conditions, to 0.1 hPa, about 65 km. In addition, the products reported values directly at the surface when possible or at the observed cloud top level. Thus in the Standard Product files, each observation could potentially contain estimates for the concentration of a particular molecule at 67 different pressure levels within the atmosphere. However, for most retrieved profiles, the highest pressure levels were not observed due to a surface at lower pressure or cloud obscuration. For pressure levels corresponding to altitudes below the cloud top or surface, where measurements were not possible, a fill value was applied.To

TL2CO2N_8 is the Tropospheric Emission Spectrometer (TES)/Aura Level 2 Carbon Dioxide Nadir Version 8 data product. TES was an instrument aboard NASA's Aura satellite and was launched from California on July 15, 2004. Data collection for TES is complete. TES Level 2 data contain retrieved species (or temperature) profiles at the observation targets and the estimated errors. The geolocation, quality, and other data (e.g., surface characteristics for nadir observations) were also provided. L2 modeled spectra were evaluated using radiative transfer modeling algorithms. The process, referred to as retrieval, compared observed spectra to the modeled spectra and iteratively updated the atmospheric parameters. L2 standard product files included information for one molecular species (or temperature) for an entire global survey or special observation run. A global survey consisted of a maximum of 16 consecutive orbits.Nadir observations, which point directly to the surface of the Earth, are different from limb observations, which are pointed at various off-nadir angles into the atmosphere. Nadir and limb observations were added to separate L2 files, and a single ancillary file was composed of data that are common to both nadir and limb files. A Nadir sequence within the TES Global Survey was a fixed number of observations within an orbit for a Global Survey. Prior to April 24, 2005, it consisted of two low resolution scans over the same ground locations. After April 24, 2005, Global Survey data consisted of three low resolution scans. The Nadir standard product consists of four files, where each file is composed of the Global Survey Nadir observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Nadir observations only used a single set of filter mix. A Global Survey consisted of observations along 16 consecutive orbits at the start of a two day cycle, over which 4,608 retrievals were performed. Each observation was the input for retrievals of species Volume Mixing Ratios (VMRs), temperature profiles, surface temperature, and other data parameters with associated pressure levels, precision, total error, vertical resolution, total column density, and other diagnostic quantities. Each TES Level 2 standard product reported information in a swath format conforming to the HDF-EOS Aura File Format Guidelines. Each Swath object was bounded by the number of observations in a global survey and a predefined set of pressure levels, representing slices through the atmosphere. Each standard product could have had a variable number of observations depending upon the Global Survey configuration and whether averaging was employed. Also, missing or bad retrievals were not reported. Further, observations were occasionally scheduled on non-global survey days. In general they were measurements made for validation purposes or with highly focused science objectives. Those non-global survey measurements were referred to as “special observations.”A Limb sequence within the TES Global Survey was three high-resolution scans over the same limb locations. The Limb standard product consists of four files, where each file is composed of the Global Survey Limb observations from one of four focal planes for a single orbit, i.e. 72 orbit sequences. The Global Survey Limb observations used a repeating sequence of filter wheel positions. Special Observations could only be scheduled during the 9 or 10 orbit gaps in the Global Surveys, and were conducted in any of three basic modes: stare, transect, step-and-stare. The mode used depended on the science requirement. Each limb observation Limb 1, Limb 2 and Limb 3, were processed independently. Thus, each limb standard product consisted of three sets where each set consisted of 1,152 observations. For TES, the swath object represented one of these sets. Thus, each limb standard product consisted of three swath objects, one for each observation, Limb 1, Limb 2, and Limb 3. The