This archive contains a geology map of the general Roosevelt Hot Springs region, both in PDF and ArcGIS geodatabase formats, that was created as part of the Utah FORGE project.

This submission contains a number of maps and shapefiles related to the Utah FORGE site. Examples include geologic maps (several variations) and GIS data for the Utah FORGE site outline. All data are georeferenced to UTM, zone 12N, NAD 83, NAVD 88.

This submission contains a number of maps and shapefiles related to the Utah FORGE site. Examples include geologic maps (several variations) and GIS data for the Utah FORGE site outline. All data are georeferenced to UTM, zone 12N, NAD 83, NAVD 88.

This is a link to Utah geology maps in both pdf and GIS formats. This includes the geology of the Utah FORGE area. This site is maintained by the Utah Geological Survey.

This is a link to Utah geology maps in both pdf and GIS formats. This includes the geology of the Utah FORGE area. This site is maintained by the Utah Geological Survey.

This is a link to the Automated Geographic Reference Center (AGRC) that houses GIS data for the state of Utah. This includes geoscience, cadastre, elevation and terrain, digital aerial photography, roads, aquifer data, etc. Several GIS datasets used in the Utah FORGE project originated from this site.

This is a link to the Automated Geographic Reference Center (AGRC) that houses GIS data for the state of Utah. This includes geoscience, cadastre, elevation and terrain, digital aerial photography, roads, aquifer data, etc. Several GIS datasets used in the Utah FORGE project originated from this site.

This is a GIS point feature shapefile representing wells, and their temperatures, that are located in the general Utah FORGE area near Milford, Utah. There are also fields that represent interpolated temperature values at depths of 200 m, 1000 m, 2000 m, 3000 m, and 4000 m. in degrees Fahrenheit. The temperature values at specific depths as mentioned above were derived as follows. In cases where the well reached a given depth (200 m and 1, 2, 3, or 4 km), the temperature is the measured temperature. For the shallower wells (and at deeper depths in the wells reaching one or more of the target depths), temperatures were extrapolated from the temperature-depth profiles that appeared to have stable (re-equilibrated after drilling) and linear profiles within the conductive regime (i.e. below the water table or other convective influences such as shallow hydrothermal outflow from the Roosevelt Hydrothermal System). Measured temperatures/gradients from deeper wells (when available and reasonably close to a given well) were used to help constrain the extrapolation to greater depths. Most of the field names in the attribute table are intuitive, however HF = heat flow, intercept = the temperature at the surface (x-axis of the temperature-depth plots) based on the linear segment of the plot that was used to extrapolate the temperature profiles to greater depths, and depth_m is the total well depth. This information is also present in the shapefile metadata.

This is a GIS point feature shapefile representing wells, and their temperatures, that are located in the general Utah FORGE area near Milford, Utah. There are also fields that represent interpolated temperature values at depths of 200 m, 1000 m, 2000 m, 3000 m, and 4000 m. in degrees Fahrenheit. The temperature values at specific depths as mentioned above were derived as follows. In cases where the well reached a given depth (200 m and 1, 2, 3, or 4 km), the temperature is the measured temperature. For the shallower wells (and at deeper depths in the wells reaching one or more of the target depths), temperatures were extrapolated from the temperature-depth profiles that appeared to have stable (re-equilibrated after drilling) and linear profiles within the conductive regime (i.e. below the water table or other convective influences such as shallow hydrothermal outflow from the Roosevelt Hydrothermal System). Measured temperatures/gradients from deeper wells (when available and reasonably close to a given well) were used to help constrain the extrapolation to greater depths. Most of the field names in the attribute table are intuitive, however HF = heat flow, intercept = the temperature at the surface (x-axis of the temperature-depth plots) based on the linear segment of the plot that was used to extrapolate the temperature profiles to greater depths, and depth_m is the total well depth. This information is also present in the shapefile metadata.

This archive contains a terrain slope image, in units of degrees, of the Utah FORGE area near Roosevelt Hot springs. The data was derived from 0.5 m resolution LiDAR DEM data and is in a GeoTiff format. It was processed using ArcGIS.