This submission contains x-ray diffraction data taken from 3,600 to 10,987 feet deep in well 16A(78)-32 in the Roosevelt Hot Springs Geothermal Area as part of the Utah FORGE project. 78 rock samples were taken. Samples are taken in a range of ten feet at 100 foot increments. Mineral abundances are given in weight percent of the sample, with results rounded to the nearest whole number. Fields marked with tr (trace) indicate that mineral is present, but that its abundance calculated from the Rietveld refinement was less than one weight percent; that it was observed in the clay-sized fraction, but not the bulk; and/or that it was observed in low abundance during petrographic analyses. The samples were taken between 10/29/2020 and 12/24/2020 during the drilling of well 16A(78)-32.

X-ray diffraction (XRD) results from cuttings samples collected during drilling of Utah FORGE well 16B(78)-32. The dataset includes XRD data for 77 samples taken between 3,120 and 10,977 feet measured depth (from the Kelly Bushing, 31 feet above ground level), with sampling intervals primarily at 100-foot spacing. Mineral abundances are reported in weight percent, rounded to the nearest whole number. Entries marked "tr" (trace) indicate a mineral presence below one weight percent, detection only in the clay-sized fraction, or identification in low abundance through petrographic analysis.

This dataset from Lawrence Livermore National Laboratory (LLNL) consists of four raw X-ray diffraction (XRD) scans and preliminary results of quantitative XRD analysis. The scanned samples were prepared from four subcores, which came from various depths of the FORGE well 16A(78)-32 core. Desired core lengths were selected from available core photos (on GDR), provided by FORGE personnel, and subcored at LLNL. The XRD scans were collected in May 2023 at LLNL as pre-experimental characterization data for these subcores, which will be used in core-flooding experiments at LLNL and in triaxial direct shear experiments at Los Alamos National Laboratory as part of DOE Project 5-2428. XRD scans are in RAW file format (e.g., FORGE-5477-full.raw) and are suitable for viewing and analysis using open-source quantitative XRD software (e.g., Profex; www.profex-xrd.org ) and/or other proprietary instrument software.

This dataset from Lawrence Livermore National Laboratory (LLNL) consists of four raw X-ray diffraction (XRD) scans and preliminary results of quantitative XRD analysis. The scanned samples were prepared from four subcores, which came from various depths of the FORGE well 16A(78)-32 core. Desired core lengths were selected from available core photos (on GDR), provided by FORGE personnel, and subcored at LLNL. The XRD scans were collected in May 2023 at LLNL as pre-experimental characterization data for these subcores, which will be used in core-flooding experiments at LLNL and in triaxial direct shear experiments at Los Alamos National Laboratory as part of DOE Project 5-2428. XRD scans are in RAW file format (e.g., FORGE-5477-full.raw) and are suitable for viewing and analysis using open-source quantitative XRD software (e.g., Profex; www.profex-xrd.org ) and/or other proprietary instrument software.

Images of core samples collected from Utah FORGE well 16A(78)-32. These images were created by stitching together multiple photographs resulting in a circumferential view of the cores exterior in two dimensions. Core footages (measured depths) are indicated in the file names, and are annotated on each image. The images, of which there are 30 in the .zip file, are in a .jpg format.

This dataset contains an overview of the petrographic, X-ray Diffraction and scanning electron microscopy analyses of core samples from Utah FORGE Well 78B-32 and related data as described in the .zip folder's Description below.

This dataset contains an overview of the petrographic, X-ray Diffraction and scanning electron microscopy analyses of core samples from Utah FORGE Well 78B-32 and related data as described in the .zip folder's Description below.

This dataset contains X-ray diffraction (XRD) data taken from wells and outcrops as part of the DOE GTO supported Utah FORGE project located near Roosevelt Hot Springs. It contains an Excel spreadsheet with the XRD data, a text file with sample site names, types, and locations in UTM, Zone 12, NAD83 coordinates, and a GIS shapefile of the sample locations with attributes.

Images of core samples collected from Utah FORGE well 16A(78)-32. These images were created by stitching together multiple photographs resulting in a circumferential view of the cores exterior in two dimensions. Core footages (measured depths) are indicated in the file names, and are annotated on each image. The images, of which there are 30 in the .zip file, are in a .jpg format.

This dataset includes survey data, drilling data, daily reports, summaries of daily operations, and rig photos from the drilling of Utah FORGE well 16A(78)-32, which is a highly deviated deep well. It was completed 60 days ahead of schedule. Rig move in began 10/22/2020 and drilling commenced on 10/30/2020, and total depth was reached on 12/18/2020. Drilling was followed by a diagnostic fracture injection test (DFIT), logging, and circulating casing. The rig was released on 1/12/2021. The upper part of the well was drilled vertically through approximately 4,700 feet of sediments before penetrating into high strength, crystalline granite. The well was deviated at a 65 degree angle from vertical after reaching a depth of 6,000 ft. This angle was maintained for the remainder of the well's trajectory. The well ultimately reached a true vertical depth of 8,559 feet, and a total measured depth of 10,987 feet. Preliminary measurements indicate temperatures at the "toe" of the well will exceed 442 degrees F (228 degrees C). Approximately 74 ft of core of the granitic and metamorphic rocks that will form the FORGE reservoir was also recovered.