This dataset contains X-ray diffraction (XRD) data taken from wells and outcrops as part of the DOE GTO supported Utah FORGE project located near Roosevelt Hot Springs. It contains an Excel spreadsheet with the XRD data, a text file with sample site names, types, and locations in UTM, Zone 12, NAD83 coordinates, and a GIS shapefile of the sample locations with attributes.

X-ray diffraction (XRD) results from cuttings samples collected during drilling of Utah FORGE well 16B(78)-32. The dataset includes XRD data for 77 samples taken between 3,120 and 10,977 feet measured depth (from the Kelly Bushing, 31 feet above ground level), with sampling intervals primarily at 100-foot spacing. Mineral abundances are reported in weight percent, rounded to the nearest whole number. Entries marked "tr" (trace) indicate a mineral presence below one weight percent, detection only in the clay-sized fraction, or identification in low abundance through petrographic analysis.

This dataset from Lawrence Livermore National Laboratory (LLNL) consists of four raw X-ray diffraction (XRD) scans and preliminary results of quantitative XRD analysis. The scanned samples were prepared from four subcores, which came from various depths of the FORGE well 16A(78)-32 core. Desired core lengths were selected from available core photos (on GDR), provided by FORGE personnel, and subcored at LLNL. The XRD scans were collected in May 2023 at LLNL as pre-experimental characterization data for these subcores, which will be used in core-flooding experiments at LLNL and in triaxial direct shear experiments at Los Alamos National Laboratory as part of DOE Project 5-2428. XRD scans are in RAW file format (e.g., FORGE-5477-full.raw) and are suitable for viewing and analysis using open-source quantitative XRD software (e.g., Profex; www.profex-xrd.org ) and/or other proprietary instrument software.

This dataset from Lawrence Livermore National Laboratory (LLNL) consists of four raw X-ray diffraction (XRD) scans and preliminary results of quantitative XRD analysis. The scanned samples were prepared from four subcores, which came from various depths of the FORGE well 16A(78)-32 core. Desired core lengths were selected from available core photos (on GDR), provided by FORGE personnel, and subcored at LLNL. The XRD scans were collected in May 2023 at LLNL as pre-experimental characterization data for these subcores, which will be used in core-flooding experiments at LLNL and in triaxial direct shear experiments at Los Alamos National Laboratory as part of DOE Project 5-2428. XRD scans are in RAW file format (e.g., FORGE-5477-full.raw) and are suitable for viewing and analysis using open-source quantitative XRD software (e.g., Profex; www.profex-xrd.org ) and/or other proprietary instrument software.

This submission contains x-ray diffraction data taken from 3,600 to 10,987 feet deep in well 16A(78)-32 in the Roosevelt Hot Springs Geothermal Area as part of the Utah FORGE project. 78 rock samples were taken. Samples are taken in a range of ten feet at 100 foot increments. Mineral abundances are given in weight percent of the sample, with results rounded to the nearest whole number. Fields marked with tr (trace) indicate that mineral is present, but that its abundance calculated from the Rietveld refinement was less than one weight percent; that it was observed in the clay-sized fraction, but not the bulk; and/or that it was observed in low abundance during petrographic analyses. The samples were taken between 10/29/2020 and 12/24/2020 during the drilling of well 16A(78)-32.

This submission includes a shapefile of the Opal Mound Fault, and multiple datasets of lineaments mapped in the Mineral Mountains which overlook the Utah FORGE site, hyperlinked to rose diagrams in a polygon grid shapefile.

This submission includes a shapefile of the Opal Mound Fault, and multiple datasets of lineaments mapped in the Mineral Mountains which overlook the Utah FORGE site, hyperlinked to rose diagrams in a polygon grid shapefile.

This submission contains x-ray diffraction data taken from 3,600 to 10,987 feet deep in well 16A(78)-32 in the Roosevelt Hot Springs Geothermal Area as part of the Utah FORGE project. 78 rock samples were taken. Samples are taken in a range of ten feet at 100 foot increments. Mineral abundances are given in weight percent of the sample, with results rounded to the nearest whole number. Fields marked with tr (trace) indicate that mineral is present, but that its abundance calculated from the Rietveld refinement was less than one weight percent; that it was observed in the clay-sized fraction, but not the bulk; and/or that it was observed in low abundance during petrographic analyses. The samples were taken between 10/29/2020 and 12/24/2020 during the drilling of well 16A(78)-32.

Three shapefiles in this submission show the position of proposed seismic line surveys. The mid-crustal velocity anomaly file shows the extent of an anomalously low P-wave velocity zone in the subsurface. Two other files show the extent of known hydrothermal systems in the Roosevelt Hot Springs area. Another file shows the location of the proposed water pipeline to pump water from the supply wells to the deep drill site.

Three shapefiles in this submission show the position of proposed seismic line surveys. The mid-crustal velocity anomaly file shows the extent of an anomalously low P-wave velocity zone in the subsurface. Two other files show the extent of known hydrothermal systems in the Roosevelt Hot Springs area. Another file shows the location of the proposed water pipeline to pump water from the supply wells to the deep drill site.