Metadata record AAS_4127_antFOCE_HardSubstrateFauna contains all data sets relating to the fauna sampled from hard substrates during the antFOCE experiment, including recruitment tiles, artificial substrate units and biofilm slides. Refer to antFOCE report section 4.5 for deployment, sampling and on-station analysis details. https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127 Background The antFOCE experimental system was deployed in O’Brien Bay, approximately 5 kilometres south of Casey station, East Antarctica, in the austral summer of 2014/15. Surface and sub-surface (in water below the sea ice) infrastructure allowed controlled manipulation of seawater pH levels (reduced by 0.4 pH units below ambient) in 2 chambers placed on the sea floor over natural benthic communities. Two control chambers (no pH manipulation) and two open plots (no chambers, no pH manipulation) were also sampled to compare to the pH manipulated (acidified) treatment chambers. Details of the antFOCE experiment can be found in the report – “antFOCE 2014/15 – Experimental System, Deployment, Sampling and Analysis”. This report and a diagram indicating how the various antFOCE data sets relate to each other are available at: https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127

Metadata record AAS_4127_antFOCE_EnvironmentalData contains seafloor Ambient Light and ambient Seawater Temperature data sets collected at the antFOCE site during the experiment. Ambient Light data was collected using Photosynthetically Active Radiation sensors (Odyssey Dataflow 392 photo diode light meters) distributed around the antFOCE site as well as several inside the experimental chambers and open plots. Seawater Temperature data were collected using Onset Hoboware Tidbit v2 (UTBI-001) temperature loggers attached to the outside of various pieces of the underwater experimental infrastructure across the antFOCE site. Refer to antFOCE report section 2.3 for deployment, sampling and on-station analysis details. https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127 Background The antFOCE experimental system was deployed in O'Brien Bay, approximately 5 kilometres south of Casey station, East Antarctica, in the austral summer of 2014/15. Surface and sub-surface (in water below the sea ice) infrastructure allowed controlled manipulation of seawater pH levels (reduced by 0.4 pH units below ambient) in 2 chambers placed on the sea floor over natural benthic communities. Two control chambers (no pH manipulation) and two open plots (no chambers, no pH manipulation) were also sampled to compare to the pH manipulated (acidified) treatment chambers. Details of the antFOCE experiment can be found in the report – "antFOCE 2014/15 – Experimental System, Deployment, Sampling and Analysis". This report and a diagram indicating how the various antFOCE data sets relate to each other are available at: https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127

This data set was collected from a ocean acidification minicosm experiment performed at Davis Station, Antarctica during the 2014/15 summer season. It includes: - description of methods for all data collection and analyses. - environmental data logged throughout the experiment; nutrients, temperature, light climate. - carbonate chemistry data; pH (on Total scale), fugacity of CO2, dissolved inorganic carbon concentration, practical alkalinity, Omega calculations for both araganite and calcite. - product datasheet (including transmission spectra) of Osram 150W HQI-TS/NDL metal halide lamps.

Refer to antFOCE report section 2.3 for deployment, sampling and analysis details. https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127 The download file contains an Excel workbook with a series of data spreadsheets - one for each of the Onset Hoboware Tidbit v2 (UTBI-001) temperature loggers that were attached to the outside of various pieces of the underwater experimental infrastructure across the antFOCE site. A Notes spreadsheet is also included with information relevant to the data. Background The antFOCE experimental system was deployed in O'Brien Bay, approximately 5 kilometres south of Casey station, East Antarctica, in the austral summer of 2014/15. Surface and sub-surface (in water below the sea ice) infrastructure allowed controlled manipulation of seawater pH levels (reduced by 0.4 pH units below ambient) in 2 chambers placed on the sea floor over natural benthic communities. Two control chambers (no pH manipulation) and two open plots (no chambers, no pH manipulation) were also sampled to compare to the pH manipulated (acidified) treatment chambers. Details of the antFOCE experiment can be found in the report – "antFOCE 2014/15 – Experimental System, Deployment, Sampling and Analysis". This report and a diagram indicating how the various antFOCE data sets relate to each other are available at: https://data.aad.gov.au/metadata/AAS_4127_antFOCE_Project4127

Total carbon dioxide and total alkalinity analysis of niskin bottle samples collected on CTD casts. All data have been stored in a single excel file. Measurements were made on the CEAMARC voyage of the Aurora Australis - voyage 3 of the 2008-2008 summer season. See other CEAMARC metadata records for more information.

During the ice stations, measurements of the air CO2, concentration for CO2 flux between sea ice and atmosphere were made with the chamber technique. Air-sea ice CO2 fluxes were measured over the sea ice with semi-automated chambers. Sample air from the chamber is passed through Teflon tubes connected to non-dispersive infrared (NDIR) analyzer (Model 800, LICOR Inc., USA) that was connected to a system controller and data logger (Model 10x, Campbell Scientific Inc., USA), that controls the opening/closing of the chambers as well. During the observation period, the CO2 flux was measured under three different conditions or surface types: (1) a chamber was installed above snow; (2) over the bare ice after removing the snow; (3) slush layer after removing the snow and slush crystals. The CO2 concentration in the chamber was measured every 5 s during experiments lasting 20 minutes for each chamber. A one hour cycle of measurements therefore consist of three 20 minute periods from each chamber (i.e. surface type). Data available: excel files containing sampling station name for each spreadsheet, dates, sampling time and air CO2 concentration as output voltage from NDIR (to indicated as ppm we need to calculate, but, not yet done this process) in the air and chamber for CO2 flux measurement. Also see the record - SIPEX_II_Gas_Flux

During the ice stations, sea ice, brine/slush, snow and under-ice water sampling were collected for CO2 concentration measurement as dissolved inorganic carbon (DIC). Ice cores were collected using a Kovacs 9 cm diameter ice corer. The ice core for DIC was cut directly after retrieval with a stainless steel folded saw. The core was cut generally into 10 cm sections (20 cm when ice cores were higher than 200 cm) and put into zip-lock polyethylene bags. Care was taken to use laboratory gloves when collecting the cores. For brine sampling, partial core holes were drilled into the ice (so called sackholes), usually to a depth of 25 cm and 50 cm. At site with flooding, brine collection was not possible, and samples of the surface slush were collected instead. Slush was collected by plastic shovel. Snow samples were also collected. Under-ice water was collected with a Teflon water sampler (GL Science Inc., Japan) 1, 3, 5 m below the bottom of the sea ice. In addition, CTD water sampling was examined at each station. The cores were taken back to the ship, and transferred to the gas tight bag (GL Science Inc., Japan), and then ice was melted at about +4 degrees C in a refrigerator. Melted samples were sub-sampled for each component. The snow samples were treated in the same manner as the sea ice samples for further analysis. The dissolved inorganic carbon (DIC) of seawater was determined by coulometry [Johnson et al. 1985] using a coulometer (CM5012, UIC Inc., Binghamton, NY, USA). DIC measurement was calibrated with reference seawater materials (Batch AG; KANSO Technos Co., Ltd., Osaka, Japan) traceable to the Certified Reference Material distributed by Prof. A. G. Dickson (Scripps Institution of Oceanography, La Jolla, CA, USA). The standard deviation for DIC calculated from 20 subsamples taken from a reference seawater material (DIC = 2084.5 micro mol L-1) was 1.4 micro mol L-1. Data available: excel files containing sampling station name, dates, and DIC concentration.

Metadata record AAS_4127_antFOCE_SedimentFauna contains all data sets relating to the fauna sampled from marine sediments during the antFOCE experiment, including macrofauna, meiofauna, diatoms, microbes, as well as DNA sequencing conducted on some of these groups and the results of a sediment bioturbation study. Refer to antFOCE report section 4.4 for deployment, sampling and on-station analysis details. https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127 Background The antFOCE experimental system was deployed in O'Brien Bay, approximately 5 kilometres south of Casey station, East Antarctica, in the austral summer of 2014/15. Surface and sub-surface (in water below the sea ice) infrastructure allowed controlled manipulation of seawater pH levels (reduced by 0.4 pH units below ambient) in 2 chambers placed on the sea floor over natural benthic communities. Two control chambers (no pH manipulation) and two open plots (no chambers, no pH manipulation) were also sampled to compare to the pH manipulated (acidified) treatment chambers. Details of the antFOCE experiment can be found in the report – "antFOCE 2014/15 – Experimental System, Deployment, Sampling and Analysis". This report and a diagram indicating how the various antFOCE data sets relate to each other are available at: https://data.aad.gov.au/metadata/records/AAS_4127_antFOCE_Project4127

The Antarctic Fast Ice Algae Chlorophyll-a (AFIAC) dataset is a compilation of currently available sea ice chlorophyll-a data from land-fast sea ice (i.e., excluding pack ice (see ASPeCt-Bio, Meiners et al. 2012)) cores collected at circum-Antarctic locations during the period 1970 to 2015. Data come from peer-reviewed publications, field-reports, data repositories and direct contributions by field-research teams. During all campaigns the chlorophyll-a concentration (in micrograms per litre) was measured from melted ice-core sections, using standard procedures, e.g., by melting the ice at less than 5 degrees C in the dark; filtering samples onto glassfibre filters; and fluorometric analysis according to standard protocols [Holm-Hansen et al., 1965; Evans et al., 1987]. Ice samples were melted either directly or in filtered sea water, which does not yield significant differences in chlorophyll-a concentration [Dieckmann et al., 1998]. The dataset consists of 888 geo-referenced ice cores, consisting of 5718 individual ice core sections, and including 404 full vertical profiles with a minimum of three sections. Samples/sections from the remaining cores represent: i) bottom 0.05 m only (n= 32), ii) bottom 0.1 m only (n = 301), complete cores (n = 66), as well as intermittent profiles (n = 85) with at least 3 sections but gaps in-between them. For questions about this dataset please contact: Klaus Meiners and Martin Vancoppenolle This data compilation was carried out under the auspices of the Scientific Committee on Antarctic Research - ASPeCt program and the Scientific Committee on Ocean Research (SCOR) working group on Biogeochemical Exchange Processes at the Sea-Ice Interfaces (WG-140). It also contributes to SCOR WG-152 on Measuring Essential Climate Variables in Sea Ice (ECV-Ice). An update to this dataset was submitted in September, 2018.