This submission includes an Excel spreadsheet containing the Utah FORGE deep well 16A(78)-32 planned trajectory including UTM coordinates, elevations, and depths from the well head to the toe. This proposed new injection well is expected to descend vertically to a depth of approximately 1810 m and then extend laterally at an angle to a MD of approximately 3290 m and a maximum vertical depth of approximately 2584 m. There is approximately 1500 m of basin fill at the well head, and less than that above the simulation region with the targeted reservoir region fully enclosed in granitoid basement. The last 60 m of the well will be open hole. Drilling is planned for October 2020. Please direct questions to the Utah FORGE team: utahforge@utah.edu and check the Utah FORGE website: https://utahforge.com after October for more information.

This dataset includes survey data, drilling data, daily reports, summaries of daily operations, and rig photos from the drilling of Utah FORGE well 16A(78)-32, which is a highly deviated deep well. It was completed 60 days ahead of schedule. Rig move in began 10/22/2020 and drilling commenced on 10/30/2020, and total depth was reached on 12/18/2020. Drilling was followed by a diagnostic fracture injection test (DFIT), logging, and circulating casing. The rig was released on 1/12/2021. The upper part of the well was drilled vertically through approximately 4,700 feet of sediments before penetrating into high strength, crystalline granite. The well was deviated at a 65 degree angle from vertical after reaching a depth of 6,000 ft. This angle was maintained for the remainder of the well's trajectory. The well ultimately reached a true vertical depth of 8,559 feet, and a total measured depth of 10,987 feet. Preliminary measurements indicate temperatures at the "toe" of the well will exceed 442 degrees F (228 degrees C). Approximately 74 ft of core of the granitic and metamorphic rocks that will form the FORGE reservoir was also recovered.

This dataset includes survey data, drilling data, daily reports, summaries of daily operations, and rig photos from the drilling of Utah FORGE well 16A(78)-32, which is a highly deviated deep well. It was completed 60 days ahead of schedule. Rig move in began 10/22/2020 and drilling commenced on 10/30/2020, and total depth was reached on 12/18/2020. Drilling was followed by a diagnostic fracture injection test (DFIT), logging, and circulating casing. The rig was released on 1/12/2021. The upper part of the well was drilled vertically through approximately 4,700 feet of sediments before penetrating into high strength, crystalline granite. The well was deviated at a 65 degree angle from vertical after reaching a depth of 6,000 ft. This angle was maintained for the remainder of the well's trajectory. The well ultimately reached a true vertical depth of 8,559 feet, and a total measured depth of 10,987 feet. Preliminary measurements indicate temperatures at the "toe" of the well will exceed 442 degrees F (228 degrees C). Approximately 74 ft of core of the granitic and metamorphic rocks that will form the FORGE reservoir was also recovered.

Utah FORGE has been established to develop, test, and improve the technologies and techniques required to develop EGS-type geothermal resources. Drilling of the first of two deep deviated wells, 16A(78)-32, will begin in the second half of 2020. This well will serve as the injection well for the injection-production well pair that will form the heart of the laboratory. This submission contains an archive of well location data within the Roosevelt Hot Springs geothermal area. An Excel spreadsheet is included containing updated GPS data for Utah FORGE wells drilled during Phase 2C (56-32, 68-32, 78-32). This data was collected over time by the Utah Geological Survey and contains all coordinates collected and the final averaged XY coordinates in both Longitude and Latitude and UTM Zone 12, NAD83. Elevation is also included. GIS shapefiles with well points are provided in the archive.

Utah FORGE has been established to develop, test, and improve the technologies and techniques required to develop EGS-type geothermal resources. Drilling of the first of two deep deviated wells, 16A(78)-32, will begin in the second half of 2020. This well will serve as the injection well for the injection-production well pair that will form the heart of the laboratory. This submission contains an archive of well location data within the Roosevelt Hot Springs geothermal area. An Excel spreadsheet is included containing updated GPS data for Utah FORGE wells drilled during Phase 2C (56-32, 68-32, 78-32). This data was collected over time by the Utah Geological Survey and contains all coordinates collected and the final averaged XY coordinates in both Longitude and Latitude and UTM Zone 12, NAD83. Elevation is also included. GIS shapefiles with well points are provided in the archive.

This is a 74 page detailed summary of the drilling activities of Utah FORGE 16A(78)-32, a highly deviated well completed on February 2nd, 2021, as part of the Utah FORGE project. This well was deviated at 65 degrees from vertical after reaching 6000 feet in depth had a total measured depth of 10,987 feet. The report summarizes the operations, lessons learned, and recommendations for each drilled section of the well.

This is a 74 page detailed summary of the drilling activities of Utah FORGE 16A(78)-32, a highly deviated well completed on February 2nd, 2021, as part of the Utah FORGE project. This well was deviated at 65 degrees from vertical after reaching 6000 feet in depth had a total measured depth of 10,987 feet. The report summarizes the operations, lessons learned, and recommendations for each drilled section of the well.

This dataset encompasses the collected data and associated reports from the low-rate injection circulation test conducted on wells 16A(78)-32 and 16B(78)-32 in July 2023 at Utah FORGE. It includes comprehensive raw circulation data, captured by Pason and Schlumberger (SLB). The dataset details various parameters recorded during circulation testing such as produced fluid, injection pressure, injection rate, produced rate, temperature, downhole pressure difference, bottom hole pressure in the well, and surface treating pressure. Note that the Pason data is presented in Mountain Time, whereas the SLB data is in Pacific Time.

This archive contains a GIS point feature shapefile that shows the locations of wells in the general region of the Utah FORGE project, near Roosevelt Hot Springs. This includes Utah FORGE deep well 58-32 and wells for which data has been uploaded to the Geothermal Data Repository. The attribute table has a field that contains well names.

This archive contains a GIS point feature shapefile that shows the locations of wells in the general region of the Utah FORGE project, near Roosevelt Hot Springs. This includes Utah FORGE deep well 58-32 and wells for which data has been uploaded to the Geothermal Data Repository. The attribute table has a field that contains well names.